Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
Hello,
Is the Power Profiler App capable of calculating and outputting the cumulative energy output to the device under test (when in Source meter mode)? I am using the...
Hi!
There is two things confusing to me about taking IQ samples in AoA application.
1. It is clear to me that that the time between switching of antennae (TSWITCHSPACING...
Hello,
I am using the Nordic SDK v1.5.0, the modem firmware is mfw_nrf9160_1.2.3 and the DK for the nRF9160
In our application, we are using AT commands to setup and control...
Hi,
There is a similar case:
High power consumption in sleep mode after using SAADC
But I am using the SAADC driver version 2.0 because the oversampling feature is only...
I have seen multiple posts about the nrf5340 that confuse me. Posts like this one say that the board/chip is not available yet, as of 4 days ago. But after looking through...
Hi,
I am new to the Nordic Semi world, having recently purchased a nRF52840 DK board and a nRF52840 dongle.
I have programmed an Arduino Nano 33 IoT over BLE and when...
We experience a 15-20% rate of dropped advertisements from our nRF52840 device. We have used our own application on our device and the ble_app_att_mtu_throughput application...
I am using an nRF52832 to talk to a Melexis MLX90393 (which supports 400kpbs Fast Mode) via the TWIM interface. I am using the TWI Manager library to schedule transactions...
See the below stack trace using nRF5 SDK 17.0.2, where execution had stopped while entering a critical region during an interrupt event when another log was being processed...
Hello,
I am developing a BLE peripheral with three services:
Device Information Service
Custom service #1 with two characteristics
Custom service #2 with one characteristcs...
When i enable BLE_DFU_SUPPORT_ENABLED 1 and debug i have problem Mesh error 4 at 0x00000000 (:0). I'm using sdk: 17.0.2, sdk_for_mesh: 5.0.0. Board nRF52840 DK. Thanks you...
Hello!
I am sending MQTT commands over UART from an NRF52840 DK to the NRF9160 DK which has the ibasis sim card inside. I noticed 3 times so far that after 24 hours , 1...
Hi
I could test Bluetooth Mesh Chat sample on nRF52833-DK nodes. I would like to know whether there is any way to send chat message from nRF Mesh app (non-mesh BLE device...
Hello,
I need to send and receive UDP packets using nRF9160DK via NB-IoT network. I'm able to achieve this using Serial LTE modem . However I need to write my own application...
