hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Hello,
I want to add the Thingy 91 to the nRF Connect Cloud. The SIM was activated correctly. I've inserted the SIM card and know I'm waiting for the LEDs to blink yellow...
Hi, I am using the UART over BLE example + a timer interrupt + a pwm signal. And I am facing the following problem (error launched by my phone app: ) This happens sometimes...
Hi ,
In order to capture and get the data from the external BLE beacons,
I am trying to simulate this using nrf connect Advertiser option instead of using Beacons...
Hello, i have been unable to read data from my sensor.
uint8_t SPI_ReadByte(uint8_t RegAddress) { ret_code_t retCode = NRF_SUCCESS; //start reading sequence m_tx_buf[0...
The modem reports that it supports states 0, 1, 4, 20, 21, 30, 31, 44 when I give the "AT+CFUN=?" command.
Using the at_client sample, or other software like asset_tracker...
Hi, I am using nRF52 DK with s112 and SDK V15.2.0. I have written an application based off of the uart example, and expanded it rather substantially to use the SAADC and read...
Hi,
I'm trying to create my switch_event by using Event Manager.
And I got this issue: "undefined reference to `__event_type_switch_event' " when submitting my event:...
Windows 10, Segger V4.52c, S132, SDK 15.2.0, nRF52832
I've been through a few posts talking about needing more RAM allocated to the SoftDevice when other services are added...
Is it possible to generate a DFU package for both bootloader-only and fully-programmed (bootloader, softdevice, and app) chips? I'm unable to do so for an nrf52833 using nrfutil...
Converting old code for a nRF51822 to the new SDK(15.3.0) for an nRF52832, this error happens:
#error "Compiler generates FPU instructions for a device without an FPU (check...
Hi all,
After wasting so much time trying to set up simple peripheral device whitelisting single central device, I realised that API has been updated and those old examples...
Hi all,
Can I read the chip ID of NRF24LE1 in code? how can I get the ID?
Or is there any readable identifier that make each chip "unique" from each other? Because the...
