I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
Hello
I have ported the example project "nrf_crypto_aes_pca10056" to my one project. But now I'm not able to building the project anymore. Segger Embedded Studio will show...
Members
I am in the board design phase of my project. I use Arduino boards (Due & Uno) with SPI. I read that the nRF24L series is not recommended for future projects....
Hi,
So I am using nRF51822 chip to develop our products. We have two motors attacked to our PCB and we want to control the pulse with low power PWM. We want to control...
Hi...
i want to read the data from another board using serial uart .. how to write the command to check the data is available ... in arduino i written like this how to write...
Hello,
I used to use two nRF52810 for testing.
Using Timeslot (BLE+ESB), one of the 52810 paired mobile phones Bluetooth simultaneously sends the ESB.
Another 52810...
What are all the configuration options necessary to configure the nRF9160 as a SPI slave? I'm working with a custom board and have specific DTS files I'm working with. Here...
Hi Nordic Team,
I'm quite confused and can't find a concrete answer so far on the forum, if it is a MUST to kick-off a certification at the Bluetooth SIG Group or not, if...
nRF52840 SDK 15.2
I want to control the power of sensor, so I configurate the pin like this:
nrf_gpio_cfg(AFE4403_PIN_PWR_EN, NRF_GPIO_PIN_DIR_OUTPUT, NRF_GPIO_PIN_INPUT_DISCONNECT...
HI,
I am using ".\nRF5_SDK_15.3.0_59ac345\examples\peripheral\wdt" to test “watch dog timer function.
My use case is:
1. If the program is not execute over following...
I have developed ble periphleral device to send 20byte long at every five seconds to the central. Because connecting to serial to PC, I didn't realize the device cannot not...
Hi,
I need to run RTC simultaneously with Softdevice without external low frequency clock source (32.768kHz oscillator).
I used following settings to setup RTC,
RTC_ENABLED...
I am trying to make a central device that is similar to the NUS central example in the SDK. I have a function that is the same as ble_nus_chars_received_uart_print to print...
In the ESB stack, only a sub-set of available transmitter powers are enumerated in nrf_esb_tx_power_t.
Is this deliberate? The hardware supports a much wider range of values...
I Performed a clean reinstall of all tools and packages.
core_cm4.h file exists at location: C:\..\..\..\..\..\Nordic\nRF5_SDK_15.3.0_59ac345\nRF5_SDK_15.3.0_59ac345\components...