Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hi,
What should i do after i load mesh app in " github.com/.../nRF51-ble-bcast-mesh" adress?i have two board
When i download the app,why doesnt advertising exist.i cant...
hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
Hi,
I followed the tutorials shown below:
infocenter.nordicsemi.com/index.jsp
I downloaded SDK v11.0 and loaded S130 SoftDevice on my nRF51 DK. I use Keil uVision 5...
I am working on a bootloader for a client. I’ve been looking at the DFU example that Nordic has. The BLE version of the DFU needs to have the special format using the “nrfutil...
hi:
I use bootloader example of sdk 9.0.0 ,most cases worked fine, but I got gatt error sometime when I begin DFU. I had changed the dual_bank_ble_s110 into sigle_bank_ble_s110...
The nRF51 reference manual says that GPIO PIN_CNF registers are retained registers and that "a retained register is a register that will retain its value in system OFF mode...
Hi,
I'm trying to add second service on the fly, while SD running. After adding it, I'm trying to send service changed notification, but it don't work. Below is code used...
Hello.
I test nrf51822 central and peripheral.
I want to change radio channel frequency about nrf51822.
I test source code as below.
nRF51_SDK_10.0.0_dc26b5e\examples...
there is an error on softdevice on src\ll_adv.c on line of 659 . what is the reason?
this is my adv init
#define DEVICE_NAME "navid" /**< Name of device. Will be included...
hi
I want to know whether we require MCU for enabling "Enhanced shock burst mode " or when we set the CE pin to high for making RX that time automatically this will enable...
Hi everyone,
I am using the nRF51822, I have an issue of programming the bootloader.
It is said that the flash is not erased. But I just did an erase all before programming...
Hello,
I have two questions regarding nRF52832 ADC, which are not documented :
what is the precision / tolerance of the internal 0.6V reference?
what is...
hello there,
I use currently 'ble_app_hids_keyboard_s132_spi_pca10040' app of SDK11 for my nrf52832_xxaa device on 'IAR' IDE. It utilizes sofdevise s132. I do not use the...
Hi
I'm encountering a problem in UART communication with nrf51422 on a custom board over an FTDI USB-serial converter ic.
When I send a string > 40 chars from the terminal...
hi
i have nrf51422 sdkv6 ss10 v1
i have timer2 inited
after something like 30 minute that it work right it stop without any system or ble event and it goes here
...
ibeacon noob here, I see several postings about implementing with different chips. Is there a preferred solution for an ibeacon for new designs? Thanks!
So I've been following these blogs on getting Monitor Mode Debugging working with SEGGER Embedded Studio: devzone.nordicsemi.com/.../ and devzone.nordicsemi.com/.../
These...
