hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
I'm starting to use Wireshark a little more and sometimes it is not displaying all of a device's manufacturer data. For example on some devices it is not displaying the manufacturer...
hi,
As a ambitious tech lover i bought BLE400 nrf51822 motherboard. I downloaded SDK 11.0, keil and nrfgo. I started programming based on the Nordic developer Zone. I first...
Hi, I try to connect nrf51822 and use example "ble_app_hids_mouse". I can pair this device and I confirmed that "Notify" becomes automatic at that time in Enable.
But, when...
Hello,
I am working with the Enhanced ShockBurst protocoll on a nRF52832.
For synchronization reasons between several nodes I need time stamps in my data packet...
hi, i build a test project to test IAP(in system program) function of nrf24le1. the project just did follow things:
1. setup uart;
2. erase page 30
3. write data "0xaa...
I'm new to nrf8001
I'm trying to understand an existing example.
in this example after sending set up commands generated by nrfgo studio , program sends 9 byte of 0xff command...
I downloaded central and peripheral ble UART and I want to add some function to my code and use some GPIO, I programmed nrf51822 by nrf51422 source code and it worked, but...
hi there!
i'm struggling with the problem about using i2c with IoT SDK.
my project is about transferring sensor data (i2c) through ipv6 over ble , so i used the IoT softdevice...
I'm considering purchasing a nrf51 sniffer USB dongle. I believe I can use this to sniff beacon packets and with wireshark view the packet internals, data, channel number...
Hi
I tried to flash the softdevice with nrfprog, but it does not work. Even with nRFgoStudio it does not work.But with IAR I can program an example of the SDK (without...
Hello, all
I have a problem with ble data exchanging.
I have programmed an application which controls servo motors through phone application.
At the connection, ble...
Hi,
I am trying to use the SAADC to periodically sample an input from AIN0 and send the resultant data over a BLE link to a phone. Going through the forums I saw that the...
Hi,
I am trying to debug the blinky example project on the nRF52 development kit.
I have followed the following tutorial: devzone.nordicsemi.com/.../
Building and flashing...
