I'm using S332 0.9.1 with freertos. nRF52.
BLE and ANT are both active. I would like to run the ANT continuos wave (CW) test after a specific trigger (a command over a console...
I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
We love the radio range of the Nordic bluetooth chips. I am looking to see if anyone is developing a long-range bluetooth pendant or wearable? if so, I interested in perhaps...
I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
Does rbc_mesh_value_enable() API is designed for ? and how should I use it? and what does its parameter handle mean? Is it has the same meanning as the parameter handle of...
I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Excuse me:
As shown in the figure below, can this type of crystal oscillator be used on nrf52832? How to connect this crystal oscillator with XC1 and XC2 of nrf52832?
Hi,
we are preparing for certification and are about to test with the DTM v1.0. now in nAN43 it states following:
1.1.1 Hardware requirements • nRF8001 Development Kit...
I try to add pairing/bonding to the NCS hello world project. But I found the information is not easy to find. I'm playing with the bt_conn_auth_cb struct to understand how...
Hello,
I am trying to verify a signature with the `NIST p-256` curve. I had previously done this with the Nrf5 sdk and it is working:
I am now trying to migrate...
Hello Nordic Team,
as a newbie in the Nordic world, I have been reading the nRF Connect SDK and Zephyr documentation as well as testing some of the samples on my nRF5340DK...
Hi.
I have some trouble to use a sensor based on JDY-23 module with nrf52832 dk
(JDY-23 datasheet : ://fcc.report/FCC-ID/2AXM8-JDY-23/4936741.pdf )
We tried to connect...
Hi,
Is LLPM over the air compatible between nRF52840 and nRF5340 devices?
I am aware that LLPM is not fully supported yet on nRF5340. Also, any update on the LLPM support...
We are hearing solder bridge issues on the NRF52832-QFAA:
"Due to the high thickness of the copper layer and small lead spacing on the component, the boardshops are not...
I am working on customizing the DFU bootloader (to add encryption). When attempting to use the instruction trace in Ozone to debug, I see a lot of nonsense. One example is...
I've been analyzing various nRF52 devices and noticed that there is an inconsistency with vendors using Legacy DFU and Secure DFU. Or in other words, there doesn't seem to...
Hi everyone,
I am experimenting with the QSPI example provided with SDK 16. I am facing issues when I try to erase memory blocks or the entire chip.
1. First of all I...
Hi, what I want to achieve is to do a list of devices that I may want to connect to, choose one and pair/bond it (at this point, the central is paired with only one peripheral...
Hello DevZone,
I have recently received the nRF52840 Dongle and I'm able to program it properly with the nRFConnect App. However, when I try to program it with the nRF52832...
Hello
I am using SDK v17.0.2 and nrf52DK. I am trying to encrypt and output the saadc value of the sensor.
I used the AES CTR example almost exactly the same.
And I...
