We are having a slight issue when we are trying to update the DFU. The original version had this setting for the data reserve:
#ifndef DFU_APP_DATA_RESERVED
#define DFU_APP_DATA_RESERVED...
Hello!
I am working with the example mpu interface projects located at the following repo:
github.com/.../nrf5-mpu-examples
After converting the Keil projects to...
I'm using S332 0.9.1 with freertos. nRF52.
BLE and ANT are both active. I would like to run the ANT continuos wave (CW) test after a specific trigger (a command over a console...
I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
We love the radio range of the Nordic bluetooth chips. I am looking to see if anyone is developing a long-range bluetooth pendant or wearable? if so, I interested in perhaps...
Hello. I'm researches the power consumption in System Off mode for nRF52810 chip. I use the next code to enter to System Off:
Chip is goes to System Off and average consumption...
Hi Nordic,
We have done some research on the DHT22 and the results showed that this sensor has excellent performance. Sadly it appears that neither the nRF9160 nor Zephyr...
Dear Nordic Team,
We have a problem in our project with custom PCB regarding DFU. It happens in most of our prototypes, but on some devices it doesn't happen.
Below...
I would like to self-provision my smartphone. Do you know how can I do this?
Then, I read that a smartphone must connect to a proxy via GATT bearer (hence a connection)...
I am new to nRF SDK. I am starting development for my nrf52810 based board. I am using blinky example from nRF5 SDK. I am using nRF52 DK board to flash and debug my nRF52810...
In our setup we are sending one CoAP message every hour. The transmission is set to be done at hh:00. Downstream communication is only required as a response to the upstream...
Hi, My name is Philex Fan who is a researcher working in academia. I am working with a group of researcher to develop biomedical device that can get brainwave signals and...
Hi!
This tutorial is just for current > Measuring current . I want the same for latency with code.
I'm working with two nrf5340 for Bluetooth low energy and I want to...
Dear Community,
From a provisioner, I want to get the MAC address of a device (provisionee) during the provisioning process. Is there an example somewhere in the forum please...
Hello,
I am using nrf52805 processor, nrf sdk v16.0.0 and Segger embedded studio. My board communicates with a temperature sensor over I2C. The software is working without...
Hi all,
I am working on a ble5 beacon with ecdsa signature. I would like to use mobile to verify my message. As I see that the crypto ecdsa example use raw key and generate...
I have developed an APP using SDK 15 (both BL and APP) updating Bootloader and APP which is working fine.
I have developed same app using SDK 17.0.2 (both BL and APP)
...
Hi, I know this topic has been up in several posts before, usually ends with, buy a LitePoint or Anritsu.
Assuming you want to do a poor mans measurement setup, just relying...
Hello, I've been trying to get the nrfx_i2s driver working with Zephyr, on the cpuapp core of the nRF5340. After configuring the driver, setting CONFIG_NRFX_I2S in prj.conf...
I've been successfully creating custom services, but there is one case where a device has a service UUID and it's 2 characteristics have completely different UUIDs (all 128...
