I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hi,
I use nrf51822 HID keyboard.
How to add a game-pad report as a second report in the ble_hid_keyboard ?
How to init the function hids_init() in SDK.
Thanks
Gamepad...
VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
Hi Nordic,
I am using one NRF52840 named A chip(DCDC mode) to provide VDD power supply to another NRF52840 named B.
A is using VDDH with battery 4.2V power supply.
B...
Hi,
I am using nrf5340 kit. I would like to enable and test power management in mesh chat example.
1. Can you please tell me the usage of below config file usage.
#define...
Using: NRF52840, SDK 14.2, S140
My GPIO initialization code is as follows. This is the first thing that happens in main.c.
Here are logic analyzer traces of 2 GPIOs...
Hi
We would like to adjust the pin matching of our nRF52805 design since the measured S11 coefficients in Tx mode are not very good (well above -3dB). The values for the...
Hi.
I am testing a wearable device based on nRF52832 and it does not have a reboot button.
Sometimes the device gets stuck and does not appear on Bluetooth scans. Rebooting...
Hello, I'm in Zephyr OS build v2.3.0 and NCS v1.3.0. I need to reprogram UART0 baudrate at run time to 38400. After having obtained the uart node
uart = device_get_binding...
I want to transmit UART and Bluetooth through 12bit ADC 12k sampling.
I downloaded the following example and verified the ADC-UART AND Bluetooth communication. https://github...
Hi,
I use the nRF52840 chip, which is designed as a module.
I use nRF9160 DK to burn the hex file.
1.And i can use nRF connect to read the ic of the module.
But...
Hi there, We're using SDK 16.0.0_98a98e2. Our setup is a PC running BLE Central connecting to 2 nRF 52840 running as BLE peripherals. We use the provided BLE UART example...
Dir Sir or Madam,
I defined 2 properties in sensor_server mesh example,
Precise Present Ambient Temperature (0x0075) and Present Indoor Relative Humidity (0x00A7) ,
...
Hi,
I use sd system power off to go into sleep mode. I wake up with the help of a button. However, the 1 second wake up time is too much for us. Do we have a chance to set...
I am currently trying to send indefinitely large files over BLE. To do this I have a central and peripheral application running between 2 nRF52840's (one peripheral, one central...
Hi,
NRF52832, SD S132 7.0.1, SDK16, custom device, custom SW
The: custom device not bonded.
In my firmware I can run beaconing in parallel with connectivity advertisement...
