hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Dear Nordic,
We are developing the Cat M1 module base on the nRF9160 V1.2.0.
When we try to evaluate the current consumption in eDRX mode, we found our module even unable...
Hi,
We made a custom board with nRF52 and it's BLE radio doesn't advertising, not visible on nRF connect APP. I tested a lot of example, like uart_peripherial,heart rate...
Is it possible for the Android-nRF-Mesh-Library to be used to serve models and also proxy/relay other on-Android nodes?
I’ve developed an Android 8 app for a tablet and...
Hi Nordic Tech Support,
Our company is going to use Nordic nRF52832 on our next generation wireless product. I am the software engineer and doing the evaluation these days...
I am using Thread/ZigBee SDK v4.0.0 as a coordinator. I have no zigbee routers in the network so all of the end devices in the network join the coordinator. When I issue a...
My current project has DFU enabled through the secure BLE bootloader and it works well. I would like to include the additional option of performing DFU over USB. Is it possible...
Hi, I'm testing the MQTT implementation integrated in the NRF5 SDK.
This is my test environment: - A nRF52840 board with the MQTT publisher example from the SDK. - A Raspberry...
Hi,
We want to be able to upload a new firmware in my nrf52832 without serial connection.
I am trying to set up DFU over BLE and I stumbled upon few problems along the...
I'm porting an application from nRF52832, SDK 14.2.0, SD 5.0 to nRF52833.
I want to do this in two stages:
As quickly as possible validate our first prototype board...
Hi,
Using the RTC example in the 'nRF5 SDK 16 / examples / peripheral' as a starting point, we've programmed the rtc_handler to execute at regular intervals approx. every...
We are using libnrf_cc310_0.9.12.a. This doesn't work with position independent code check box in IAR (see Project Options->C/C++ Compiler->Code->Code and Read Only Data ...
Hi,
I'm trying to enable a HW timer (TIMER1) in my BLE application. I'm using SDK 16, and following the pattern shown in examples/peripherals/timer. However, when I get...
Hello
We have a project in which we need to be broadcasting data (around 30 bytes of message) to 150 unit via BLE.
we are thinking of using the nrf52832, which we...
Is it possible to read the value of APPROTECTSTATUS via the firmware? It seems like the AP register in not memory mapped, so maybe not. But maybe there is some kind of work...
Hi!
I'm trying to transfer data from UART to BLE in NRF52810. NRF52810 connects MSP430 controller via UART, MSP430 sends packet of 16 bytes lenght every 2ms (500 times in...
