hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Hi,
here is the situation:
Compiler: VS 2017
CMake: 3.12
boost: 1.67.0
pc-ble-driver branch: master
Firstly I can successfully build the pc-ble-driver, with this...
So I came from the arduino world and made my life simple by making a resitor bridge with buttons so that I could spare many pins for other features. I have problems finding...
I'm trying to understand which part of the code provides the bluetooth connection between two nRF52840. I worked in sdk15.0.0 with multilink, blinky and uart examples to solve...
Hi, everyone,
We are developing project with nRF52832 chip.
For making it's monitoring we used UART communication port. But on the next step of development we had to enable...
I need to interface an nRF52832 with ADS7042, hence the following questions:
1) as ADS7042 requires 14 clock cycles per read cycle, is the nRF52832 SPI API applicable in...
I am constantly receiving an NRF_FAULT_ID_SD_ASSERT error within a non-deterministic time after connecting via BLE.
The program Counter is always 75936 and Info == 0. I...
Hi
Development Environment : windows 7- keil ARM SDK 5 - Arm Debugger Programmer(Waveshare) - nRF51822 EVK from Waveshare
What is the boot_PIN or Boot_Mode PIN
I want...
I am wanting to increase the length of one of my characteristics used when my device is acting as a peripheral. When I increase the size of my characteristic, the softdevice...
Hi,
I needed some figure for my controller selection,
Please if can you tell tthe exact answer it will be very help full,
Using NRF serial example for uart with baud...
Hello,
I have a voltage divider/thermistor circuit where R1 is an NTC thermistor of 100kOhm at 25 ° C. R2 is 100kOhm right now.
I took peripheral_saadc example for SDK15...
Hi all,
I'm testing out and adapting the Thingy Mesh Demo v0.1 , which uses nRF SDK for Mesh v1.0.1 for my internship. I will be testing out a Thingy's Mesh network for...
Hi,
I tried, ble_blinky example on DK, it works well. Also advertising interval 40ms on nrfconnect mobile app,this is consistent with SDK.
Now, i try same example with...
Hello
My name Ilya, am from global company Rosslare -access control. i am a R&D lieder.
I have found that nRF52840 is accepted to my new project - BLE reader.
I want...
Chapter "18.6.1 Power-on reset" of the data sheet describes " A step increase in supply voltage of 300 mV or more, with rise time of 300 ms or less, within the valid supply...
