hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Hi Sirs:
I am trying to change a characteristic property from "notify" to "indicate".
And the example I used was SDK15-> ble_app_uart .
I have ref these document:
...
Hi,
I'm trying to implement the buttonless DFU service example for SDK 12.3.0 into my own project, but when I call ble_dfu_init my compiled .hex file becomes 10 kb larger...
Hi,
I am working on SDK-14.2 and after execution of code i get this two error mention below.
sd_ble_cfg_set() returned : Unknown issue when attempting to set BLE_CONN_CFG_GAP...
Hi I have implemented a controller device using nRF52832. The controller device is installed in an industrial control box where it is used to control relays that subsequently...
Hi,
This question might be a little bit off, but not to far off for this forum I hope.
I am considering the nRF52840 Dongle to gain a better understanding of a issue...
Hi guys,
I need to get MAC address of my device and put it into characteristic? Is it possible? And maybe someone can tell how to implement this?
Regards,
Konstant...
Hi:
I use heart_rate_collector project in pc-ble-driver ( https://github.com/NordicSemiconductor/pc-ble-driver/blob/master/examples/heart_rate_collector/main.c )to connect...
Hello,
we are studying component base for development Wireless Hearing Aid device.
trying to understand limitations and capabilities of your nRF51822 SoC.
1. Can...
When test the current in the WFE state.
If not use the DMA, the current is not exceed 0.1mA. And when have used the DMA, the comsumption is very high , the current is about...
Hi,
We have a custom board with nRF52832 QFABB0 chip. High frequency crystal used is 32MHz (Part No: ECS-320-8-37CKM ) with two 12pF load capacitors (Part No: 80-CBR04C120F5G...
Hi All,
As "Mesh beaconing example" work as a advertiser and at a same time it scan beacon also.
I just want to use only beacon scanning functionality in this application...
Hi
I have moved an application from Softdevice 130 V5.1 (with SDK 14.2) to Softdevice 130 V6.0 (with SDK 15) both using keil.
My BLE peripheral device name is Nordic1234...