I'm using S332 0.9.1 with freertos. nRF52.
BLE and ANT are both active. I would like to run the ANT continuos wave (CW) test after a specific trigger (a command over a console...
I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
We love the radio range of the Nordic bluetooth chips. I am looking to see if anyone is developing a long-range bluetooth pendant or wearable? if so, I interested in perhaps...
I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
Does rbc_mesh_value_enable() API is designed for ? and how should I use it? and what does its parameter handle mean? Is it has the same meanning as the parameter handle of...
I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Are there any native RTOS build-in the SDK? If I need to develop a sensor device driver (i2c based) any recommendation as the safest way to do that. Choosing between freeRTOS...
Hi,
there is a broken link on https://www.nordicsemi.com/DocLib/Content/SDK_Doc/nRF5_SDK/v15-2-0/ble_sdk_app_buttonless_dfu that refers to " Generating bootloader settings...
I'm writing a production script that uses nrfutil to do OTA DFU for both nRF51 and nRF52 radios. I'm using a PCA10059 with nrfutil version 3.5.1.
It works fine for an nRF52...
Hello,
I am trying to use IAR examples to debug some of the examples provided in the SDK.
I am only using examples that support the pca10059 dongle.
One example is the...
Dear All and @rogerclark,
From the release note of nRF5 SDK v14.1.0, Segger Embedded Studio (SES 3.30) IDE has been supported originally.
I use MacOS, and I has set...
I need a help to create a mesh where two nrf52 dk are connectred in the mesh and one node sends a message and another node recives it and sends to a url
I am currently looking at how to put the nrf52 development board to sleep (and wake up) by sending a command from an android application (with SDK v15.2).
I have been experimenting...
Hi
I am trying to establish communication between a NRF24L01+ and an NRF51822, but unable to do so. I am able to communicate between 2 NRF24L01 + and also between 2 NRF51822...
Hello, I'm quite new to both the nRF52832 and the Segger Embedded Studio. I have a college project which involves I2C communication with 2 slaves. I was finally able to set...
Hello,
I am trying to read data from a sensor through sensor TX pin connected to RX pin of nrf51822. Nrf51822 recieves this data through RX pin and sends it via bluetooth...
I am seeing a problem using the nRF52 SAADC with two analog channels enabled in scan mode.
Essentially, channel 0 is measuring an analog signal with gain ~= 15 while channel...
Hello,
I am trying to get the RX interrupt to trigger on the PCA10001 board using the segger debugger as my serial terminal.
My hardware setup consists of a PCA10001...
SDK: v15 SoftDevice: S132 Chip: nRF52832 on BL652 Module
I have a command->response type system. The Central (Android phone) sends a command, and the Peripheral (nRF52 device...
Greetings!
I am using nRF52, SDK14.2, and NUS with MTU = 64. I want to transmit 1000 byte string over BLE upon reception of any character to "nus_data_handler" I have divided...
