hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
I am using mesh sdk v2.0.0 1, 1 client and many server node is successfully provisioned. But when i increase CLIENT_NODE_COUNT (2) instead of 1 only one client is provisioned...
Hi all!
I'm currently trying to communicate with the CR95HF (on the BM019) chip over SPI with the DK52 board.
I'm using SDK 15.0
According to their datasheet, the CR95HF...
Hello,
When I analyse the output of my radio, I see that I have a spurious frequency at 12,8 Mhz.
I supply my custom board with a fidelity power supply so no problem...
So I have implemented the UART BLE mesh code as mentioned in devzone.nordicsemi.com/.../send-and-receive-a-string-via-access-layer .
Now I am able to take inputs from the...
Hi,
1.
I feel really stupid as I cannot make any sense of any of the information found in Product Specification (v3.3), or the online Compatibility Table or past forum...
We can know the state of radio by checking NRF_RADIO->state register value, but is there any way that we can be "informed of" the state transitions of this register instead...
I want to demo the NFC provisioning example on Github. Unfortunately this app is not complete.
https://github.com/googlesamples/android-NfcProvisioning
Is a complete...
Hi. I'm using nRF52832 SDK 13.0.0.
My device is peripheral and it is advertising every time.
Now I want to change advertising packet and scan response packet every time...
Hello:
We have a BLE project running on the BMD-300 from Rigado for which we want to add BLE DFU functionality. I am basing our development on the "ble_app_buttonless_dfu...
Hello,
I want to measure the current in system off mode.
I am flashing the S110 softdevice and bootloader in the nrf51822 chip.
Using BLE i am flashing an application...
Hi nordic
I'm developing using nrf52832
This board has many example code so I'm developing smoothly
but Today I had problem. It is about check time
I want to check...
Hello, I use light switch example (nrf52832, mesh sdk 2.0.1)
Can I create mesh network without servers? (clients will send messages to each other and process them)
And...
Hi, I want to use 2 I2C instances and 2 SPI instance during setup, and later switch to 1 I2C instance and 3 SPI instance. To do this, I tried to swap TWIM2 instance to SPIM2...
I'm looking to build a product which require an Android board with relay and BLE 5. I am very new to this and so far I have been playing with Raspberry Pi where the BLE and...
