here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi There,
Our peripheral firmware running nrf5 cannot seem to connect properly to our central running NCS 2.4.1 over BLE. We are consciously setting the connection to use...
Dear Nordic Support-Team,
the provided samples in nrf-SDK are great to show how to use several aspects of the nrf Sdk and the devices.
Nevertheless it would be great if...
I am planning to create an application on NCS that can have https://github.com/nrfconnect/sdk-nrf/tree/main/samples/bootloader using CONFIG_SECURE_BOOT=y, But is it possible...
TLDR; Need advice on which wireless communication protocol to use for five nRF52840 dongles within 75 feet of each other. I've never worked with Nordic Semiconductor products...
I'm experiencing an issue with I2C communication between the SEN5X sensor and multiple nRF9160 DK boards. The problem manifests as an crc error during I2C read operations...
In case I run the code from zephyr/samples/bluetooth/broadcast_audio_source, I get following error, when I play audio:
After I stop the audio, the log messages stop...
Hi,
I'm pretty new to Zephyr and I have to figure out how to connect to a NOR flash over SPI. Final application is the implementation of a file system, e.g. littlefs.
...
Hello !
I recently updated our project SDK from 2.6.0 to 2.7.0 and our custom board to HW v2 layout. Everything went almost seemless until I tried to enable sysbuild option...
We created a product using nrf52840. the product is operating well, but it has been confirmed that software reset (0x04) operates in very few times (2weeks per 1time). In...
Hi,
We have previously realized the nRF7002 Matter project. We tried this with nRF52840. I am using Amazon Dot 4 but Amazon did not detect Matter. What is the reason for...
Hi:
I checked the zephyr.dts file, but why are the addresses for flash_controller: flash-controller@39000 and kmu: kmu@39000 the same? I checked the specification and 3900...
Hi,
One question, in VS code,
when I choose the nrf5340dk_nrf5340_cpuapp for build configuration, the VSCode told me the nrf5340dk_nrf5340_cpuapp is without security,...
Hi,
I get a very strange issue. Below is my device information:
NCS v2.4.0, Zephyr
It acts as a Peripheral
It advertises itself, accepting connection
Connection...
Hello, The following warning occures when I build the SLM Shell sample (Not changed original code).
[Build Configuration]
Target sample: SLM Shell ( https://docs.nordicsemi...
