Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
Hi,
We are developing our own board with nrf6190. I already flash the chip with nrf9160dk_at_client_2024-03-13_af2b60d2 application and mfw_nrf9160_1.3.6 modem application...
The customer wants to do wireless approval now, before using the DTM mode, the version available on the old computer is selected, the device can be found on the old computer...
When I click on flash, to flash the blinky program onto the nRF5340 DK board, I get this error message:
FATAL ERROR: required program nrfjprog not found; install it or add...
Hi
I need to send data from nRF7002 to external CPU(STM32) use UART protocol, for HW nRF7002 P0.20 connect STM32 RX and RF7002 P0.22 connect STM32 TX, I try to use exercise...
Hii,
i used nrf5sdk and i am trying to scanning i2c address of Sensirion sgp40 Sensor but unable to sacn i2c address.
I try SGP40 sensor with arduino code its work correctly...
I have tested NPM1300-EK with NRF52840DK and it works.
However, I am using other MCU with NPM1300 but it is a non -zephyr project.
To work with NPM1300, I have tried...
Hi,
I am using nRF7002 DK. I have set P1.04 as UART RX. For testing I am using TI CC26x2R1 Launchpad to send UART data to nRF7002 DK. I use a logic level shifter board to...
Hello,
I am currently trying to connect an external hardware codec and amp (Adafruit MAX98357 I2S Class-D Mono Amp) in order to play audio via BLE Audio and I2S using...
I have an NRF9161DK 1.0.0 , I was trying to do some wiring but the sensors didn't work, then I noticed that the board delivered 1.7v.
I tried changing it to 3.3v using the...
Hi,
My NRF52840DK ( pca10056 1.1.0 2019.9) would not reset when I press its Reset button. The issue is very similar to https://devzone.nordicsemi.com/f/nordic-q-a/38555...
I have new Thingy 53. Default Edge Inpulse demo works without any problem. But I have problem with Weather Station demo.
First I tested Zigbee version. After flashing using...
Hi,
What is the minimum LDO dropout voltage of nPM1300? For instance, in order to get 3.3V from the LDO, what is the minimum input for the LDO ? On the datasheet there is...
Dear all:
I have prepare env for border router successfully following this link( developer.nordicsemi.com/.../tools.html , Raspberry Pi4 and nRF52840( RCP: radio coprocessor...
