here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi:
I use sdk:nRF5_SDK_17.0.2_d674dde and NRF52840.
Reference examples:nRF5_SDK_17.0.2_d674dde\examples\peripheral\uart
PC connection RX-pin20 and TX-pin22, PC sends...
Hi,
We are looking to purchase the nRF52832 SoC. The data sheet says it supports a data rate of 1Mbps when the receiver sensitivity is set to -103dBm. This data rate is...
I am experiencing a strange behavior with SES 6.32, using GCC and I wonder if I should choose a different compiler.
COMPILING THIS PART OF CODE (I added line numbers for...
I want to add wifi connectivity to asset_tracker. It is required that MODEM is turned off. The program flow need to change so that instead of Modem, wifi Module is tried first...
Hello,
I am trying to read a 32-bit value over BLE but the value displays as 8-bit on nRF Connect. In my code I am sending it as an int32. Why does nRF Connect only show...
Hi There,
I have almost done the project, I used nrf52832 as central(master) and nrf52810 as peripheral(slave).
i use the blinky example and everything working fine. I...
Hello,
I am using nRF52840 and I currently am working on a application where mostly I am using central functionality (BLE connection and exchange the data) along with cellular...
I'm willing to use the 5 claused licensed code for the parts that only work with nordic hardware, but the partition manager isn't actually necessary. Is there some way to...
Hi,
I am trying to migrate a moderaely complicated nrf5340 app from sdk 1.9.1 to sdk 2.0 and having a few issues with getting the right crypto configuration. Original...
Hello, guys！
I'm currently just starting to work on the nrf9160dk board. I want to try to explore the communication of nrf9160 with external acceleration sensor. First,...
Hi Team,
Is there any blog/tutorial on how to add custom profile (service/characteristics) with ncsv.1.8.0 and nrf52832/33?
I could find a couple of blogs but they were...
Hello everyone, I'm testing the example ble peripheral "UART/Serial Port Emulation over BLE" with SoftDevice S112 nRF5 SDK v17.1.0 . My board is MBN52832DK and i'm using the...
Hi,
in my project I use the nRF52840 microcontroller as the master I2C device.
Sometimes the TWI peripheral SDA line is forced to a low value by the slave device. This...
