here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
I am using nRF52840DK for working on my application. I use nRF Connect SDK v1.9.1 to run example and build application. I use VS code to build the application. I am working...
HI
Saw the youtude video: https://www.youtube.com/watch?v=dpvNXQiLbh4
For BLE Audio Broadcast mode, could i check how many channels of audio can be broadcasted and selectable...
I'm developing firmware for a custom board developed with the nRF5340. We opted to use RTT as our logging/shell output as opposed to UART thanks to pcb size limitations. I...
Hi,
We are porting some of our old firmware from SDKs <= 17x to nRF Connect SDK.
We have not found a way to access several of the drivers, like pwm_nrfx.c and use functionality...
Hi,
I'm trying to build the nRF5340 Audio sample application for the nRF5340 Audio DK board and get this error message when creating the project:
Any thoughts?
Regards...
I'm trying to migrate from the nRF52832 to the nRF52833 using the same exact code, but the nRF52833 does not go into low power mode. The nRF52832 consumes 100uA with the nRF52833...
Hello, I have successfully connected two NRF5340s using central_uart and peripheral_uart and can send messages to each other. But I don't know how to test the data rate.
I have an implementation that is using a PWM output to drive a LED. It has been observed that when the LED is on in a constant drive state, fixed PWM output train, the LED...
I would like to communicate at a speed of 1ms or 2ms if possible, as I need to make a gaming mouse with as little latency as possible. To achieve this, I plan to use the nRF52840...
Hi Team,
could you please help us how to remove service change characteristic?
Also please share us how to SET PHY as a constant "BLE_GAP_PHY_1MBPS" ?
please suggest...
The following code got NRF_ERROR_INVALID_STATE. What is meaning of NRF_ERROR_INVALID_STATE? And when will NRF_ERROR_INVALID_STATE generated?
err_code = nrf_drv_gpiote_init...
Dears,
The customer wants to know that the Thingy53 evaluation board can calculate the 3-axis acceleration,angular velocity,magnetic field, these 9sets of data into "quaternion...
I want to remap SPI0 pins from default (P26, P27, P28) to another ones (P08, P09, P10) on PCA10040 under nRF Connect SDK. But I stuck into a problem: SPI module seems to work...
Hi,
I just go a question about when to use the nrf_moden_lib_shutdown(). Is it necessary to use in this code case? Since I've used lte_lc_power_off().
Regards,
Elia...
Hi
1. I tested function NRF_LOG_INFO and found that NRF_LOG_INFO automatically prints the \r\n character
2. How can I remove the \r\n character
Thank you for all...
