here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hello !
In PS1.7 chapter 6.4.5 Encrypting packets on-the-fly in radio transmit mode is explained encryption of a short packets (MODE.LENGTH = Default).
But when MODE...
Hi there, I'm performing an throughput analysis using an nRF52 development board (BMD-350) and a Raspberry Pi 4B (Ubuntu 20.04, BlueZ 5.54) with an BLE 5.0 adapter. For measuring...
Hi,
I want to use the bsp button to our project, so I tested on the example "ble_app_blinky",
I modified the app button to bsp button, add two custom events to the bsp_event_t...
Hi Devzone,
I've been trying to verify and validate the performance of Instaburst mesh packets against regular ones. I modified a build of the mesh light switch example...
Hello,
I have been trying to get the thingy:91 up for 3 weeks or more now from Sri Lanka. I have made a lot of progress in getting data connectivity via MQTT to thethings...
`Hi There,
For nRF52840 board, If I want to fully disable JTAG or SWD lines after flashing, then what are the options to achieve it.
Questions:
1) If I want to disable...
My use case: There are different but similar peripherals advertising with 1M uncoded or coded PHY. Some of them are even advertising in mixed mode.
Question: How to connect...
Hello all,
I hope you are well. I am currently developing a product on the nrf52810 platform. I have a custom board and now have the BLE functional on the board. The next...
Good Day.
I want to measure the approximate voltage level on the battery in the nrf52820 microcontroller using a comparator (COMP) operating in Single-ended mode. I use...
am following the introductory videos and have done a fresh install of the Toolchain, Segger, VS Connect 3.7.2, nRF Connect SDK v1.8.0 and VS code on macOS
1. Installation...
Hi team,
I'm currently playing around with the sensor server example where I wanted to include the generic_onoff model in a separate element. I wanted to learn how to add...
Sure, my question is very stupid, but after one day I found nothing to explain the principle of the situation, I decided to ask.
I have a laptop with built-in Bluetooth...
Hi all,
I am trying to interface IS25LQ040B serial flash(512KB) IC with nrf52833 (bl653_dvk).
programmed sample code from "zephyr\samples\drivers\spi_flash"
I am getting...
Hi all, im asking question about triggering my own antenna. there's few questions about it. 1. im using TI boostxl antenna array (3 antenna) , periodic table are as follow...
