I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
We love the radio range of the Nordic bluetooth chips. I am looking to see if anyone is developing a long-range bluetooth pendant or wearable? if so, I interested in perhaps...
I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
Does rbc_mesh_value_enable() API is designed for ? and how should I use it? and what does its parameter handle mean? Is it has the same meanning as the parameter handle of...
I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hi,
I use nrf51822 HID keyboard.
How to add a game-pad report as a second report in the ble_hid_keyboard ?
How to init the function hids_init() in SDK.
Thanks
Gamepad...
Hi,
I successfully send the status of the button from the Switch board to the Light board in the light switch example in nRF Mesh v2.2. .But how can I send other sensor...
Dear community,
we are using nRF52840 (s140) and nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8 to develop a multiprotocol (BLE, ZB) application. Regarding the sending...
Hallo,
I try to use app_timer on the dongle to raise an interrupt every 5 min.
The goal is to send the µC in power save mode and every 5 min, it shall wake up, measure...
In the NRF5 SDK 17.0.2 ble_nus_c.c are two calls to the evt_handler without setting event.conn_handle.
Please find attached a patch to fix this for on_hvx() and ble_nus_c_on_ble_evt...
Hi,
I'm trying to figure out what could make the current consumption difference between your blinky example with freertos and with the timer example ?
Here is my configuration...
Hello, this is my current setup: - nRF52840 acting as NUS peripheral, with properly configured coded phy (nRF SDK) - nRF5340 acting as NUS central, with properly configured...
Dear friend，
I am doing a test like this: 1. Connect the Bluetooth device with the nrf conncet app of the Android phone. 2. The notify (CCCD) is enabled. 3. Click "disconnect...
Hi,
we are using D- and D+ in our nRf52833 board, I want to use the CDC ACM USB class as Virtual COM port.
I found that there has a demo example in the \examples\peripheral...
Hi,
We have a problem that occurs when
1) the GPS is at bootup of nrf91: indoor when we start the GPS search, and it doesn't find anything or maybe just 1 satellite...
Hi,
Looked through PS v1.3 didn't see any reference, so probably the answer to my question is no.
But can you please confirm that for me - does nRF52833 support boundary...
Hello,
I am doing tests on nRF9160 DK and I observe that if I send more than 1024 bytes on a TCP or UDP socket, the bandwidth drops.
Here are some numbers :
for...
Hi there
I mount the 19pin connector on nrf5340dk board and connect to segger j-trace pro . The debugger function work well.
Later i modify the nrf9160 etm trace project...
Has anyone had success getting triggers on motion to work with the LIS2DH? I only have INT1 wired so I modified the drivers to work on INT1 as the spec document says it should...
I'm writing software for nRF52832 using nRF5 SDK v17.0.2
I'm using a timer to create a buzz/tone using timer 3. This works as expected.
I'm also using the SAADC to measure...
