void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
Dear ,
On Windows 10 Bluetooth add a device,
Why SDK_17_0_2 Example does Bluetooth be disconnect immediately after pairing
(Use about \nRF5_SDK_17_0_2\examples\ble_peripheral...
When I open the Light Bulb project in Segger Embedded Studio I see a bewildering list of project items. I pick the first project, 'zephyr/merged.hex' and right click to set...
SDK: 4.1.0
CHIP: 52840
Hi, I have developed sleepy zed. It lost the connection with the network after joining in 1~3 days.
It assumes that the zed couldn't get the...
Hi, guys.
I'm using nRF52 DK (PCA10040). After I used Zadig (Driver setup for J-link), I cannot build and run my previous code to the nRF52 DK anymore (see the first 3 images...
Hi
I am using nrf52840 boards and by using the coexist program I am able to send and receive messages through mesh while using the ble services.
I followed the instruction...
I use NRF52DK as central device I also use a SDK that is ble_app_uart_c code for my project. and i would like to take my peripheral devices whice are phone or PC their RSSI...
Hello - we're using "nRF Connect" from the Apple App Store for the development of our project.
First, thank you for making this tool available and free for everyone to use...
I am using nrf52840 via NRF Connect and Zephyr configured to use the Nordic SoftDevice BLE controller.
My use case is for a central to sample a rapidly changing real-time...
As a beginner,I’m sorry for asking such a stupid question,but it has annoyed me for a long time.
I built and downloaded the program to my DK,and I used PuTTY to connect...
Hello,
I've designed a pcb using the 52840 chip which is essentially identical to the dongle design. My intent was to use the firmware that comes pre-installed with the...
Is there a set of prj.conf settings that I can use to redirect the AT command interface to the RTT debugger? Would be nice not to have to hook up a serial connection.
Hi All,
as the title say I'd like to know if is the Wake on GPIO available for nRF52840_dongle and what is the I OFF_RAMOFF_GPIO ?
My application should behave more or...
Hello. I'm developing a project using nRF52840. I've been working with the nRF52840Dev Board and I have a BLE project that runs there. I'm developing in Segger IDE and using...
When building a product which has multiple models but the firmware is essentially the same, perhaps with a few different parameters, I want to use the same code base and have...
