hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Hi,
I'm trying to make connection between nRF52840 dongle programmed with "examples/peripheral/cli" application and Windows 10 UWP "CustomSerialDeviceAccess" example code...
Hello
Currently I use the example "ble_thread_dyn_mtd_coap_cli_pca10056" and I would like that my application can detect timeout of the messages sent on the Thread network...
Hello, First of all, I hope you are doing okay about the corona virus crisis. I wish that you stay healthy and safe . Recently, I have been trying to configure ble_app_uart...
Hi Sir,
In the datasheet (V1.1), the table-145 shows the dimensions of WLCSP, but there is no tolerance of D/E/D2/E2
Could you help to advice what is the tolerance of...
I have a project where I am implementing an alternative logging backend. My design is modular so there could be multiple logging backends. Each backend is initialized with...
UPDATES after original posting:
I now remember having the same problem described below, once before on my windows installation. At that time I decided to switch and reinstall...
I'm working with the nRF5 SDK v15.3 and a nRF52840 Dongle; developing on Keil uVision V5.29; Compiler: Armcc V5.06
While debugging I that in my programm a NULL pointer was...
HI ! I found an error in the source code because of which the db discovery event handler on DIS client does not work, namely: in the function ble_dis_c_on_db_disc_evt () ...
Does it cause issues if the application was built with a different SDK level than the bootloader? I have a project I'm adding a bootloader to, and it isn't working. I have...
SDK 16, 52810
my board has done the change as the 52810 spec says about dcdc part. Now I wonder HOW do I enable it in my code. Somewhere it says to call sd_power_dcdc_mode_set...
I want to measure the current during sleep,so I write my code as follow:
I queried the manual data that the current is 1.5uA, but 14.0uA is my measuring result. So what...
I am testing the serial interface to BLE messaging using "Bluetooth Mesh Packet Send Opcode: 0xab" - it's working very well. However I have found one thing that is puzzling...
Hello there,
I am working on secure dfu. I followed all the steps mentioned in this post and successfully created the secure .zip file.
Here's what I did(In this order...
