Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
Hi
based on nus example , I'd like to create RX/TX characteristics with a custom UUID (128bits)
My problem is about the UUID characteristics versus UUID service, for example...
I've inherited a project where the software was developed in IAR and I've rebuilt it in SES. I am having an issue configuring the memory for the soft device.
The chip is...
For a project under development I used two NRF24L01 for testing and they work very well.
Now I would like to know if: is it possible to use one NRF24L01 as TX and several...
Hi, I am working on ble_app_template. I am trying to save a value in the flash memory of nRF52840. I am using the following 2 functions to write/read in flash memory but getting...
Hi everyone
I am using app_uart_put() method for sending data via UART. The problem is that when I send each byte I get each byte back to its event handler in APP_UART_DATA_READY...
I have a Thingy:91 connected to a Garmin LIDAR Lite v4 (built on the nRF52840) via four GPIO cables. The code running on the Garmin reads one GPIO pin to signal a measurement...
Hello, I just want to clarify a secondary takeaway from my post:
https://devzone.nordicsemi.com/f/nordic-q-a/60714/best-approach-to-store-nonvolatile-data
I would like...
Hello.
I'm invesigating this on behalf of a customer.
I bought a thingy91 and wonder if it is possible to stream live video stream?
I would like to mont a camera to...
Hello everyone,
I have a Python script on my PC sending data through serial port COM5. I want to know if it would be possible to read the data sent from the PC on the nRF9160DK...
My target is porting my host MCU (STM32) to update my NRF52832 code through the serial.
I test it on SDK14.2.0 and PCA10040 , the secure_dfu_serial example is working ,...
Hello,
I experimented with some different capacitor tuning values at C1/C2; the external 32MHz clock initializes just fine for C1=C2=10pF, C1=C2=12pF (nominal), and C1...
hi ,
im try to add some consumer keys and system keys to the project:
nRF5_SDK_16.0.0_98a08e2\examples\ble_peripheral\ble_app_hids_keyboard
and my code of hids_init...
Hello! I'm trying to reach zigbee on nRF52840, and I'm trying to get a zigbee communication from light_bulb. The hex file on the sdk goes in well, and I want to add additional...
I just learn nrf52840-Dk
I can download hex and build for example light_switch mesh to nrf52840.
But light_switch project have too many C files.
Which one C file or...
