VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
Hi,
I am running NRF52840 on a custom board with SDK 15.0.0, Softdevice S140 6.0.0 and SES.
I am measuring using a toggled GPIO pin measured on a CRO. This produces a...
I'm using an nRF52DK to monitor the RSSI and MAC address of my two phones through ble_evt_handler BLE_GAP_EVT_SCAN_REQ_REPORT.
I tested both Android and iPhone. They both...
Hi all!
I have small problem. When I build my project, it returns thise error: Symbol SWI2_IRQHandler multiply defined (by nrf_sdh.o and nrf_drv_swi.o). I want to use SWI0...
Hey, I am using nrf51822 nRF5_SDK_12.3.0_d7731ad SDK and using Segger embedded studio. In the application code my memory segments is this. Now I want to do firmware update...
Hello,
I am debugging my nRF52832 with JLinkRTTClient through NRF_LOG, but there seems to be some issues I don't quite understand with the color coding of the logging messages...
Hi there, we use the nRF52840 on a embedded system. The nRF52840 is connected via usb interface to the central cpu of the embedded system. An embedded linux (buildroot) is...
Hi!
Is it technically possible to implement performing of unmodulated TX carrier transmission by a write to some BLE characteristic? If yes, then from what to start?
Thank...
Hi,
I am trying to use the Bluetooth low energy capability of the nRF9160 DK (nRF52840 chip) by using the lte_ble_gateway sample from Nordic. After changing some lines of...
Hi
I'm using ZigBee light control coordinator example in "nRF5 SDK for Thread and Zigbee v3.1.0" on nRF52840 evaluation board.
when it will execute bdb_start_top_level_commissioning...
I am runing the light switch example in zigbee sdk v3.1. I am connecting to a smarthings hub. I have set the a single change on the code:
The device will be connected...
A couple questions about the nRF52840 GPIO Electrical Specification:
1. In the nRF52840 GPIO Electrical specification, VOH at 0.5mA is spec'd to go as low as VDD - 0.4V...
Hello,
I have been using the development kit for more than a month when after one flashing, the LED 5 on the board started blinking at one second intervals and the board...
I read a nRF9160 DK 0.8.5 circuit design and have a question about the GPS circuitry. What will happen if I bring the LTE antenna closer to the GPS antenna and reduce the...
