Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
Good afternoon. I use NRF 51822, and I want to use RTC 0 or RTC 1. But there are problems, if I do not initialize BLE then the compiler does not execute LFCLK_config because...
We are now developing BLE ADC sender, using nRF5_SDK_14.0.0_3bcc1f7, and two nRF528322s (sender and reciever).
We send SAADC data via BLE, after that, we disconnect, and...
I am currently using SysTick to count milliseconds in my device. This works fine, however with it enabled I can't sleep the device as it wakes up instantly.
I have tried...
Hi,
I'm not sure if I'm doing something wrong so I'm hoping someone can help me. After updating from 0.11.4 to 0.12.0 of pc-ble-python-py, I get the following error. I've...
Hi,
Please help to suggest if 10K Nodes in a single network with 100 Kbps data rate is achievable with data transmission interval being roughly every 30 seconds.
This...
I have the debug section of the evaluation board turned off, modifications to measure current with a DMM set up, and am using a keysight 34465a DMM to measure current. The...
Here is the code snippet initializing the Heart Rate Measurement Characteristic in the BleHeartRateMonitor example:
static uint32_t characteristic_init() { uint32_t error_code;...
When using nRF Connect and 52840 Dongle, the normal BLE scan app works fine but connecting to the RSSI ap, the reprogramming of the dongle fails with timeout.
Hi,
I have nrf9160 DK.
I found there is u-blox driver available. Is it possible that the 9160 modem can be added an interface as a modem using u-blox? If so, there is...
NRF_LOG_RAW_HEXDUMP_INFO() is not printing complete Extended Advertisement data in HEX format. It just prints first 80 bytes of whole advertisement packet.
I added below...
Hi Nordic Developers,
Service Discovery Protocol (SDP) is a protocol for Bluetooth to detect the service nearby and to determine their characteristics by using UUID.
I...
Hello!
I am trying to lower the sleep current of our custom board. Right now in sleep, the whole system have a current consumption of 100uA. There might be component choices...
I get answer from msromero that If zigbee network is open, then new zed can join this network.
What means that nework is open ?
I want zigbee netork is silently joinable...
