void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
All nRF52832 based RF modules on the market have been certified using a Nordic SoftDevice. Some manufacturers say that it is ok to use a different Nordic SoftDevice without...
Hi I have been put into at task with a nrf52832 device (Mesh) that can only update the application. This is a big problem because we already have multiple device all over...
Hello. We are using nrf52840 for our product and I wanted to use aes ccm encryption for security. I was able to integrate CC310 library but I found out that encryption works...
i'm working on dynamic multiprotocol between ble and thread.
i want to ask about ble packet size in link layer and how could i change packet size ? is it could affect loss...
I am using arduino to send message through BLE to a mobile, which use "nRF Connect for Mobile" to scan the arduino.
I am able to get the information of Blood pressure (0x1810...
Hi,
We are developing a device with nRF52840 and mBed-os. We have a bootloader based on SDK 13.0.0.0-1 with softdevice s140 5.0.0-1-alpha.
Changes that has been made to...
Dear nordic,
I need a help from your side i want to create 1 hz(1000 ms time period) frequency pwm using PWM driver. i created upto 30 ms time period but i cant create time...
Hi, I'm using nrf52840 TWI master. Sometimes the I2C bus result as locked in endless loop to retry the start conditions. I see that in this case SDA and SCL are tied low for...
Updating the SoftDevice on the nRF52832 from S132 v2.0.x to S132 v3.0 using the Dual Bank Bootloader from SDK v11.0.0 results in the application not starting up after the...
I am planning to use Open bootloader example as my starting point for adding a bootloader to an application. I donot want Softdevice. Initially I am going to check the dfu...
i am working on ble_app_uart central and peripheral, so basically peripheral will sleep wake up and send advertisement packet to central . Now the issue is if peripheral is...
Hi, My Lord. When I run the example, I use short-name(BLE_ADVDATA_SHORT_NAME) advertising always "Fatal error",It's no use reducing payload.
On the other hand, how to add...
Dear experts..
I'm currently developing and testing nRF52832 application with nRF52-DK.
This are three questions about "actual" advertising packet length on air.
First...
1.HOW TO enable a node relay , friend,proxy or low power ability ?
2.if node A publish a message to a GROUP ADDRESS(0XC001) for node B( subscribeed this group address) ...
I looked at the nRF91_DK_User_Guide and it is very confusing to understand how to set up the board for current measurements. The figure says to solder SB44 and SB45 but the...
