VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
It is a fantastic tutorial, Thanks.
And I can get it to compile with SDK15.0.0 pca10040 s132. But how can I get it to work with 52840 DK?
Copied pca10056 and s140 into...
Hi all,
To keep compatible with previous devices, I need to use Enhanced ShockBurst on 52832. Now I need to add PA / LNA control to Enhanced ShockBurst, but I can't find...
Hello,
Now i want to implement Scanning and Advertising at the time using s132 on nrf52832 with SDK15.0.
I use a app_timer of 10ms to realize a dvertising every 10ms....
I have an nRF52810 on a custom board and can't get it to wake from System Off mode. The code:
trying it with a different way to turn the system off also didn't work: ...
Dear Nordic Support,
Processor: nRF52840 / S140 soft device / SDK 15.3.0
I have a question about the use of the HFCLK in relation to the soft device. Our board has both...
Take a look at a following code
void fmc_serial_rx_cb(const uint8_t* p_data, uint32_t length)
{ __LOG(LOG_SRC_APP, LOG_LEVEL_INFO,"\n-------------SERIAL RECIEVED : %s...
I am new to softdevices so please bear with me for long list of questions.
I am evaluating SDK15.2.0 examples one-by-one. I came across eddystone example (ble_app_eddystone...
Hi!
In older SDK (15.0) has been present NRF_ESB_BUGFIX_TIMER and it initialization. Now (SDK 15.2/15.3) defines this macro but not use it. Is it bug or obsolete code?
Hello Nordic Team,
I followed the tutorial as you say( https://devzone.nordicsemi.com/tutorials/b/getting-started/posts/nrf52840-dongle-programming-tutorial ). But when...
dear all,
I'm a newbie on blue tooth low energy development, I have some really basic questions that I hope someone could answer, thank you very much in advance!
what...
Hello,
trying to bring up the new nRF91 dk with default firmware.
Registered the eSIM. Switch sequence followed when LED 3 and 4 starts blinking, but get the devices list...
Hi I have central device which has array of MAC address to connect.
when i see the structure of sd_ble_gap_connect() i cannot pass a uint8_t addr[5] as input.
so i tried...
SDK v11.0 & NRF51822 QFAC
I encountered a problem. In the process of pstorage processing flash data, a serial port interrupt came in, resulting in a system reset.
I used...
Hi,
I have discovered a (rare) problem where the S132 stack get stuck in connected state when it is not actually connected anymore.
This behavior was first reported by...
