I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hi,
I use nrf51822 HID keyboard.
How to add a game-pad report as a second report in the ble_hid_keyboard ?
How to init the function hids_init() in SDK.
Thanks
Gamepad...
VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
Hi,
I want to connect NRF51822 wit NRF51 development kit over the air i-e. Development Kit would work as server (look for available client and connect with it and then send...
Hi,
I am using nrf51422 dk board in my project. so i need to use Bluetooth in my project. Could you plz tell me the which version of SDK do i need to use for this Bluetooth...
Hello to everyone.
I'm working with chip nRF52832 (PCA10040) and Mesh 3.1. I'm trying to connect a HC-05 Bluetooth/Serial Module using its serial pins (Rx/Tx) to the default...
Hi,
I am using SDK 15.3 and NRF52840 Preview DK
I have a requirement where I have to glow one of 3 LEDs R-G-B (each connected to one gpio pin) for 1 second and turn...
I'm using nrf52840 to develop a remote control using BLE long range.
We use two nrf52840 : on inside the remote and another in the system to control. The remote is used...
Hi,
I've done a lot of searching and Googling and could not find a proper answer for the life of me, so I'm posting again here to try to find answers. I must have looked...
I want to use internal temperature sensor in the example, "peripheral\temperature" on our software but there is the problem that we met when applying on board internal temperature...
I'm using nRF51DK and created 2 app_timers (based on LFCLK) that are running on 32.768kHz crystal, one for kernel timing (10ms) and one for real time clock (every second)...
Hi,
For some reasons, I would like to write my own application for updating the firmware, something like NRFUTIL application.
I wrote it and everything is working fine...
Hello,
I am trying the ble_app_cts_c_pca10040_s132 (current time service client). Under the conditions described below, ultimately a SoftDevice call to sd_ble_gap_device_identities_set...
I am attempting to integrate examples/peripheral/flash_fstorage into my project (SDK 14.1.0).
When calling nrf_fstorage_write I get NRF_ERROR_INVALID_LENGTH in response...
I am trying to provision 2 clients for the mesh so that i they all can send the message to a single server.
I will list what all i have tried
1.I took a server node and...
Our custom board uses internal RC clock source and I tried to build original sample app, "ble_app_pwr_profiling" in SDK 15.3.0 using attached sdk_config.h modified only with...
