here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
I am just starting using a Thingy:52 and want to use it with a C# UWP app. So far I have been able to retrieve the service and characteristics UUID's without issue but I am...
SDK 15.0.0 nrf52810 Example: Eddystone Beconing mode - ble_app_eddystone SEGGER Embedded Studio for ARM v4.12
I am using ble_app_eddystone example to advertise data in eddystone...
My development enviorment: SDK 15.0.0 nrf52810 Example: examples\ble_peripheral\ble_app_template\pca10040 e SES IDE
I am running above mentioned example without any changes...
Hi
I have a requirement to be able to re-start advertising with new parameters when told to do so over a Slave SPI interface. From other posts, it appears that there is...
Hello, when I use NRF52840's SDk15.2, use the usbd_ble_uart_freertos routine, I create a new task named test_thread in it, after the interrupt is disabled, the delay will...
Hi!
After one smartphone bonded and reboot nRF52, I get this error. As I readed, this is due to incorrect mac address. Can I check which part of addres is incorrect and...
I have a list profiles,for which I need to check, whether they can be implemented in BLE 4.2 or not?
The following are the profiles:-
1)Audio/video control profile.
...
my production that t he name of broadcast is "smart" and then I change the name to "Ryon" in the application and download.they all right,but The name of broadcas t was wrong...
Hello, recently I tried to establish simple SPI communication between my S6E2CC board and nRF24L01 chip. What I do is I try to read 0x05 register and the answer should be...
Migrating SPI routine from SDK13 to SDK15. The following snippet worked in SDK13, but now I get an error "'nrf_drv_spi_t {aka const struct <anonymous>}' has no member named...
Hi there,
In our firmware we have a layer on top of FDS that handles higher level file system functionality. There is room for improvement in this layer that we created...
I am using nrf52832 with sdk 13.0.0.-alpha.I only want to boot the application and jump to blinky project address.For that i am using secure dfu example code.I am using IAR...
1. Are there any examples or recommendations how to realize ota dfu of ble central (device).
2. Can nrf52840 works like ble peripheral(UART service server) for smartphone...
Hi,
I would like to know how to program the code to connect the PC based on the ble_app_template.
The SDK version I used is V11 and the board I used is PCA2006, and I...
