I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hi,
I use nrf51822 HID keyboard.
How to add a game-pad report as a second report in the ble_hid_keyboard ?
How to init the function hids_init() in SDK.
Thanks
Gamepad...
VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
Dear team,
I am trying to build my CPP project with Nordic Zephyr SDK. I am using following commands:
west build --build-dir nrf_build -b nrf52840dk_nrf52840 sample -DZEPHYR_TOOLCHAIN_VARIANT...
Hi guys,
starting to improve my throughput with an nrf52805 and S112, i know this version does not support DLE, but it's also the one with lower footprint, I will ask...
HI Nordic Team,
I am developing a firmware to interface CH101 sensor, which has a firmware loading of 2048 bytes of data over I2C.
I declared buffer size as below in device...
Hi,
As i understand from the docs, the max throughput for BLE in nrf5340 is 1.4mbps. Ideally, we would like to achieve this, however anything near to 1mbps would be great...
hello,
I would like to know which operations were performed on all chips by the `nrfjprog --recover` command.
"The nrf52833-B chip is by default enabled for read protection...
Hello everyone,
I’m new to the Nordic development ecosystem and currently working on a project to implement a temperature and humidity monitoring system using the nRF9160...
I'm currently working on a project using the nRF52840 board with the MAX30001 ECG sensor. I'm using nRF Connect SDK with VS Code version 2.6.1 to develop the project on Zephyr...
I am using nRF9160 to develop a mobile measuring device.
For this purpose I need LTE and GPS, I know it is shared so I had to implement PSM/eDRX to make it work together...
Hi
I am working with a sample project (Bluetooth: Peripheral UART) for nRF5340DK in VSCode.
So I have installed the nRF Connect extension.
When I view the currently...
\nRF5_SDK_17.1.0_ddde560\examples\peripheral\pwm_driver\pca10040 In Demo1,i assigned the same pin to the 4 channels. I expect every cycle LED0 has the same behavior. But,...
Hi Networks,
I have tried to build the nRF5340 DK as a gateway.
Enabled
1. CONFIG_BT_GATEWAY=y
2. CONFIG_BT_GATEWAY_ADV=y
3. CONFIG_BT_GATEWAY_GATT=y
But not acting...
Hello,
I will be designing a board using with nRF52833 with the NRF21540 for the added gain. Would it be possible to add adaptive frequency hopping?
Thank you,
Shah...
The central device has the below settings
One central device A and two peripheral devices B and C, B and C have the exact same firmware. A can establish the connection...
Hello
I have implemented the stereo function to the nrf5340 audio application on SDK V2.6.0. i can send stereo audio signal to both of the two headset at the same time or...
