I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hi,
Sorry, I found a similar question on this site, but I still don’t understand. We would like to demonstrate the following.
Perform distance measurements simultaneously...
Hi, We're in the product validation stage of development with nRF54L15, part of the validation is temperature cycling, we noticed that devices seem to be "stuck" in sleep...
We have transitioned over to using memfault OTA platform and used release overrides for some devices.
Is there a way to easily search for devices that have release overrides...
I'm working through the Cellular IoT Fundamentals course. In lesson 7 exercise 1 a modem trace must be captured. I'm following the instructions but the modem trace capture...
Hi,
I am experiencing an intermittent issue with the debugger in nRF Connect for VS Code version 2026.9.2823 on Windows.
Environment:
nRF Connect for VS Code: 2026...
We have an nRF5340 device that maintains a peripheral connection to a central device and then makes several of its own central connections to other peripherals. We ran into...
Hi,
I'd like to inquire what effect the SAADC TCONV parameter has on the results of the SAADC. The SAADC section in the datasheet specifies it can range from 1 to 7, giving...
Setup: nRF Connect SDK v3.4.0 (LTS), custom board based on nRF54LM20A, sysbuild with MCUboot as the only bootloader (no NSIB / b0), DTS partitions (SB_CONFIG_PARTITION_MANAGER...
Hi,
I'm sending IPv6 traffic between two PCs over a DECT NR+ link: two nRF9151, one FT and one PT, NCS 3.4.0, modem firmware mfw-nr_nrf91x1_2.0.0, using the l2_dect stack...
hi team,
i have trying to wrote a code for adc module in segger 5.40 using nrf52840 controller and i found you mentioned different frequencies for each pins in datasheet...
Hello,
Could Nordic clarify the supported deadline and recovery behavior of pcd_network_core_update() when the network core never changes its command status?
At sdk-nrf...
Hi,
We are designing a battery-powered product based on two Nordic chips and would like your recommendation on the overall architecture before we freeze the hardware, having...
Dear Nordic team,
I am trying to set up OTA updates by using the DFU target API on an nRF9151 DK with MCUboot and TF-M partitions. (NCS v3.4.1) My goal is to use the immutable...
Hello
We have nrf54l15 as a host and main MCU along with nrf9151 with SLM build.
We are connecting it to nrf-cloud, previously we used only nrf9151 with nrf52 connected...
