I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi,
I am trying to understand the pstorage to record a log for temperature. In my code, I can call pstorage_init(), and clear a block but when I try to store some data...
Hi
I use nRF7002-DK and sdk version as v2.5.2,download lesson8 exercise 3 solution and build was error as below log, which parts am I miss?
build config as below
...
Hello,
I a working on a project that uses the nRF5340 CCM peripheral (Network core) in an asynchronous mode. That is, I encrypt PDUs prior to scheduling them for transmission...
I want to configure my setup for secure boot and enable TFM and encrypted application images for firmware update. I am using nRF sdk version 2.5.0. My board is nRF9160. Now...
I have setup the UART along the same lines as the sample project in the DevZone Academy. I have extended the example provided to suit the project needs.
What I am getting...
In our custom board nrf5340-nrf7002, tried system_off(C:\ncs\v2.6.1\zephyr\samples\board\nrf )sample to check power consumption.
But it measures 0.60mA Is there any config...
Hi all, We have a custom board running with a project based with ncs v2.6.0. On our board we have two external flash, one is used for DFU the mcuboot_secondary with QSPI and...
Hello All,
I am not able to find the nrf_drv_adc related files in SDK folder. ADC library is not supported in NRF5_SDK_17.0.2 is it so?
Thanks and regards,
Neeraj...
Hi Team,
We are testing the nRF7000's Wi-Fi location feature to enhance our device's capabilities.
Our setup includes:
nRF52832 as a BLE beacon
nRF9160 as a host...
When I follow exercise steps A to open nRF connect terminal,vs code will display issue as follow:
Whether some issues happened when I get nrf connect SDK?
How can I...
Hi community,
It's my first time building a board with a Nordic chip so for sure I've made a lot of mistakes. I made this with KiCad and uploaded all the files to the repository...
What is the possible reason that LED1 blinks and LED2 does not light up when the nRF5340 Audio source is operating?
I have read and understood the source code, but I am...
We've added our app's overlay files into the mcuboot child_image directory so that mcuboot is initialized with the proper state of the board. In our nrf5340_cpuapp_common...
Hello,
Using wifi monitor sample on NRF7002 DK, packet length is constantly 70. It was checked both by reading received variable from:
received = recv ( packet -> recv_sock...
Hi Nordic DevZone Community,
I am working on a project using the Zephyr RTOS with an nRF52833 series board, and I am trying to interface with an SSD1306 OLED display via...
I have a device with a programmable output pulse width for its data ready signal. I need to be able to reliable receive the pulse so I don't miss any interrupts, and I'd like...