Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
Dear Nordic Team,
We have tested that the nrf5340DK borad was ok for the broadcast audio source role.
We want to add the nrf21540EK FEM borad on it to test the max broadcast...
Hello,
I have a question regarding sensor configuration. I am planning to use the LIS2DW12 sensor. While reviewing the SDK, I found the source code in the path sdk\zephyr...
Hi, We are developing a custom PCB which contains the nRF52840 MCU as the main MCU on the PCB. The PCB is battery powered and would need to support timekeeping even after...
Hello, I'm working with NCS 2.6.0 in Visual Studio Code
I already have a private key generated by using imgtool.py, and I put the .pem file in C:\user\nordic\ncs\user_apps...
Hi,
I am using the Nordic NRF52832_dk with SDK 16.
I need to write, read, and delete data in flash memory.
I store the data by creating a file in the flash memory...
Hello, I want to make periodically wake up nRF52840, performing some work (connecting to MQTT broker, sending some data) and after that going to low power mode. Then the nRF52840...
Hello,
We want to use a nrf52840 as a logic controller which reads data from Modbus RTU Sensors (as Modbus RTU Master) and simultaneously is the Modbus RTU Server for an...
Hello Team,
We are trying to make Release and Debug mode for our software.When I compile a sample program I see lot of Debug information in the Mapfile. Will this influnce...
Hi Support team:
I'm using Zephyr cellular modem driver on the nRF5340 and set APN in prj.conf with 'CONFIG_MODEM_CELLULAR_APN="telenor.iot"' now. I need to set APN value...
Hello,
When building my project although the terminal doesn't show me using all the RAM, I get the following error message which fails the build.
I am using a...
Hello,
I was working on a ble communication using two nrf52dk boards while one of the two stop responding. The board is correctly recognised by the computer and segger asks...
When I am on to collect the accelerometer data from Thingy-53, only 3 sampling frequency options are provided which are 20 Hz, 62.5 Hz and 100 Hz as shown in figure. Please...
I am new to nRF chips and currently working with the nRF52810. I am developing with nRF Connect SDK and VSCode.
I have encountered an issue with the Blinky example (ncs...
