void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
Hi.
We've created a custom board, and it works nicely.
However, when I try to build another application for this new board (i.e. "Add Build Configuration"), the new board...
Hi,
I'm using the nRF Connect app on android to DFU my devices.
On some occasions, after doing DFU and unbonding, the phone will keep asking if I want to pair the device...
The Absolute Maximum rating of I/O pin voltage for VI/O, VDD ≤3.6 V is -0.3V to VDD + 0.3V in Table 185. We would like to monitor the battery voltage using an AIN pin because...
Hi, We are using the SDK v17.1.0 and SD S140 v7.2.0. In our application we have to send only 1 advertising packet with updated data every 300ms and in some cases every 50ms...
Hi,
I work with win10 laptop, Toolchain nrf Connect SDK 1.6.1 on a nrf5340dk.
I modifyed peripheral_uart to use 240 bytes like it's explain into "ncs 1.6.1 peripheral_uart...
Hi, I am trying to create a custom BLE service.
Following is the main code:
These are my BLE write functions:
My sdk_config file says MAX_MTU is defined 23
...
Hello everyone,
I have a few questions related to NFC in nrf52832.
1. UUID in nrf52832 NFC is Unique?
2. Can I use nrf52832 NFC for payment purposes..? if yes How I...
Hello sir,
I am using nrf52832 soc with customised board want to use as UART pins as RX pins as 23 and TX pins as 24 .Is it possible to use the RX pins as 23 and Tx pins...
Hello,
I am trying to configure a Zigbee coordinator as done in the CLI example (for example 'bdb role zc' and 'bdb start') to get data from the multi sensor example,...
Hello,
Lately we've had some problems with DFU using the NRF connect app.
The device we are using is a nrf52832 running Zephyr 2.6 with MCUBoot 1.8
When we set the following...
Hi,
Turning on A-GPS (using the SUPL library) causes our application to encounter a boot panic ("unable to find bootable image"). Similarly, running the nRF9160 GPS example...
Hi Dev team,
I have been working with the MQTT example and building up my application. I establish a successful connection with the broker and everything runs fine for 5...
I had trouble connecting the device to the computer. My computer shows that it is connected, however, in VS code, it cannot find the device. Also, when I tried to use the...
