here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hello,
I was using the send example which is located in C:\v1.5.1\zephyr\samples\drivers\lora and trying to send a message to an Arduino LoRa gateway.
However, I found...
Hello everyone,
I am stuck at a problem that I cannot resolve myself but I see that other people in the forum don't experience such a behaviour of their nrf52832s.
I want...
Hello,
I've been using SES for ARM (Nordic Edition) V4.16 (64-bit). I am working with nRF9160 sample code. While attempting to explore the code, when I right click on...
The program flow of the slave is to sample the analog signal source through the saadc and then send it to the host through the nus. When debugging on nrf52dk, configure the...
Hi,
In my main function, I just call a acceleration_read function to get data from the accelerometer sensor and call a NRF_LOG_INFO function.
But there're something wrong...
Hi,
I try sdk 17.02 nRF52840 usb audio demo,I want to achieve 48KHz stereo music play by a I2S DAC.
I finished adding DAC for I2S to play the sound data of USB Audio...
I am declaring the variable in one of the hardware drivers files that are provided by the nordic semiconductor. The variable is not static. The variable inside the function...
Are there any other QFN package baluns that we can use for NRF51822?
One suggested from STM is BGA, and I wanted to see if there are any recommended QFN baluns that we can...
Hi Nordic,
I have an NRF52805 board [ from Raytech] and I am implementing all my application using SDK v15.1.0.
As of now, I have implemented my application using the...
Hi,
We need to know rated output and gain of pcb antenna on nRF52 DK for a technical standards conformity certification.
Can you give us them and their evidence?
Thank...
I want to connect an LTE antenna to J1. However, the antenna has a normal male ufl connector - it appears not to fit.
Is an adaptor needed for this?
Thx for any suggestion...
Hi ,
my environment details:
nrf connect sdk
nrf5340 dk
segger embedded studio
I have seen I2C example code in below path
\v1.5.0\zephyr\samples\drivers\i2c_fujitsu_fram...
app_timer2.c from SDK v17.0.2 has a possible race condition in app_timer_start()
This calls the get_now() function which compares a "now" variable to a "m_stamp64" variable...
Hi,
I am developing based on the mesh dimming example.
I want to use a timer for some status LEDs and some other things. I am trying to do it using timer 0, but the callback...
Excuse me:
The default stack stze setting of SDK is 8K,If the stack overflows when the customer reads data from flash， Does stack overflow modify other...
