here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
I am using the sdk-zephyr. After configing the ubuntu enviroment, i use the west build commond to build the sample project.
But there are errors like these:
[0/1] Re-running...
Hello,
I have few questions about PPI.
----------
1. How to configure PPI channels that runs one after the other? If yes, is there any example?
Because I have two...
I'm having trouble getting the Secure Entry gateway functions to work out of RAM. The nRF9160 datasheet has RAMNSC configurations, so it should be possible. We're able to...
Hello,
I'm not able to locate the QDID for S113 v7.2.0, associated with nRF52832 and SDK 17.0.2.
The product page for S113 indicates that S113 is Bluetooth 5.1 qualified...
Hello,
two part question;
-when a device is registered with the FCC, there is a good amount of documentation uploaded to the FCC website like test reports, photos of the...
Hi I'm wondering if anyone has any tips on implementing a I2C recovery sequence with NRFX 2.3.0 (as included with Zephyr 2.4.99). I've seen this discussed https://devzone...
Based on zigbee sdk 4.1, in the sample code of light_switch, leaving the network and joining the network are completed by buttons, the code is as follows:
Seen from the...
Hi, my BLE application on nRF52832 is designed to select two mode to operate with 3 position slide switch when power on like ON(Mode 1) - OFF - ON(Mode 2).
At Mode 1 position...
Hello.
I'm using nrf52840 to sample the voltage from the wireless board and then send the data to the PC via Bluetooth.
With the help of DevZone, it was able to construct...
Hi,
I have downloaded and installed nRF Connect for desktop - Bluetooth Low Energy. Now I want it to operate as a peripheral that can send connectable advertising packets...
I'm having an odd issue with libUARTe sending a TX buffer twice.
I have a custom board using an nRF52832 running an application based on SDK 15.3.0. The libUARTe code was...
Doing development on nRF52 DK board using buttonless DFU example and SDK 17.0.2. Running SES on Win10 and gnu compiler.
I've set up a 1 mS timer to run timing in my main...
I am using the ble_app_uart in combination with the f_storage example to write data to the flash memory. A issue which arises is that, when a softdevice is enabled, the nrf_fstorage_nvmc...
