Hi,
I am trying to understand the pstorage to record a log for temperature. In my code, I can call pstorage_init(), and clear a block but when I try to store some data...
I would like to source a compact BLE board to act as a lock controller developed with with a matching transceiver for use in a fob and an app.
It would toggle the pio and...
Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello all,
I am having a problem to get SAADC to work with low power. I am using custom board with chip NRF52811, SDK 16.0.0.
I had turned on the SAADC_CONFIG_LP_MODE...
Hello Everyone,
I am using my custom board with nrf52832 SoC and developing my application firmware with sdk15.2 & softdevice v6.1.0.
In my application code, BLE scanning...
Hi,
We were trying out the LTE RX/TX test using the AT%XREFTEST command and undestood that for LTE RX testing ,an external signal generator is required. Is there any way...
Hello
I would like to know if there is a capability of a truly secured boot with the nRF53, starting with a secure bootloader in some locked or immutable memory - i.e. secure...
Hi team
I did follow the getting started assistant to set up software tools and clone sdk ncs 1.3.0.
Verified successfully at getting started assistant, too.
But, when...
Hi
I have some issues with nRF52810.
I am trying to use SPI as a Master on a custom board. I saw here that nRF52810 does not support legacy SPI : https://devzone.nordicsemi...
Hello,
We are adding BLE scanning to an ANT product.
We have been using SDK 10.0.0 from the beginning, so we use the Example below.
SDK 10.0.0.0\examples\ble_central...
Hi Supportor
I have two board, if I didn't set the gain, which used default of SDK, one board output value is 0x2f5, another output ADC value is 0x266.
I set the gain...
Hello,
I'm having issues with what I believe are interrupts, if I use the bootloader.
I'll give a brief description of the issue I faced, and then I'll state how to reproduce...
Hello,
Is there any documentation available that specifies what version of nrfutil is required to create DFU packages which are compatible with a SDK and/or soft device...
Hi
I am using NRF52 with 512KB flash, and with SDK15.2
I am not using DFU
I tried to protect the program flash pages using "sd_flash_protect".
I tried to protect pages...
Hi everyone,
Currently I'm using Android Nrf Mesh Library 2.4.1 for provisioning device into network.
I face the issue which can not be found why to fix this error.
...
I cannot set CONFIG_POWER_OPTIMIZATION_ENABLE to yes in the master branch. It leads to deadlock in at_cmd_write() because that ends up getting executed in the socket_thread...
I copied the slm application into a directory outside the SDK (e.g. C:\temp\slmapp) and I launched a command prompt from the nRF Connect's tool chain manager. Then I navigated...
