I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi,
I am trying to understand the pstorage to record a log for temperature. In my code, I can call pstorage_init(), and clear a block but when I try to store some data...
Hi support team,
I've been developing a project that uses a cycling cadence sensor and interacts with my nRF52840 DK which is the central device. I merged the rscs central...
Hii
I'm using nrf5_SDK_for_Mesh_v2.0.1_src with nRF52 DK. i have tested your light switch demo by creating provisioner, proxy client and proxy server on individual NRF52...
Hello, I'm newbie developer.
I want to create a program that ends advertising when I press the button and restarts press it again.
I've seen many examples, but I can't...
Hi Team Nordic,
I know this question has been answered in several threads but the responses seem quite old now. I am using nrf52840 and SDK 15.3.0 and I want to flash...
Module : EYSHJNZWZ (nRF52832)
Is there a way to check nRF52832 IC revision? Since the chip is embedded in the module, it cannot be confirmed by appearance.
Hello,
I am working on developing a program where the nRF52840 dongle is a central device and recognized as an HID keyboard to the computer.
I played around with the peripheral...
I am trying to get a periodic interrupt every 100 uS using TIMER4. My timers_init() code sets up the TIMER4 registers as follows:
My interrupt service routine for now...
Hello
I would like to evaluate the module in a place without Cat-M \ NBIoT support
is it possible (for evaluation purposes) to send the data by other means (for example...
Hi,
New to Nordic, new to SEGGER, and new to ARM, so forgive me if I'm just missing something...
I've been asked to write new code for some boards that have the nRF51822...
I am using the SPIM example in the nRF52840 SDK. It uses SPI_INSTANCE 3. I am doing a simple SPI Write of 2 bytes.
I get SS, SCK, working properly. MOSI is transitioning...
I want to take drive code from thingy sdk and apply it to nrf5 sdk uart project, but I don't know how. Please explain in detail because i'm university student ... thank you...
Hi Team Nordic,
I am trying to save my flash data after the DFU process but it keeps on erasing it. I saw a thread in which it was explained to increase the CODE_PAGE_SIZE...
Hello,
I have a problem with app_timer.
My program need to use BLE UART for about 15 second then switch for just RADIO after.
To do so, I enable the ble stack as...
hello support team
nRF52 DK , Mesh 2.01
I am trying Experimental BLE RELAY example.
1. In first trial I am using 1 RELAY DK all works well.
2.In second Trial I am...
Hi everyone, I have a custom board using nRF52832 chip.
I want to turn ON and OFF a LED, which is directly connected to a GPIO pin.
Using this configuration I expect...
