void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
Hello,
I want to get the raw acceleration of the Thingy 52. however I can't understand the values I get from the raw acceleration. What is the unit used for raw acceleration...
I am using Nordic SDK 13.0.0 with PCA 10040 dev board.
I have configured the stack to use MAX_BLE_MTU_SIZE = 200
// Configure maximum size of ATT packet the SoftDevice...
Hi,
I encountered a weird behavior. i defined characteristics with specific read/write permission however all the characteristics are writable for some reason altough the...
Given this error handler function...
and this logging from it with the Segger attached...
how do I debug this?
I presume the info passed in is bogus and just points...
Hi All,
I'm currently using SDK12 for nRF52832. In my BLE peripheral project I store central address who engaged my device to listen for ANCS notifications. This address...
Dear Nordic Community,
I am using the the nrf51 dev kit to try and program a custom board (nrf51822) connected to it via the the Debug Out connector. This setup has worked...
Hi,
I'm testing nRF52832 central data rate.
My SDK version is 14.0.0 and softdevice is 5.0.0.
I want to send 200byte from nRF52832 peripheral to nRF52832 central in one...
Hi,
I'm using NRF52840 with Softdevice and SDK v15. I would like to use an external 32.768kHz crystal.
If I understand correctly this is consistent with the eval board...
Would you please provide an example of using PA/LNA with nRF52840 (Softdevice S140) on SDK 15.0 or higher?
Unfortunately, I could't manage the code you've provided for the...
Hi With regards to iOS and Android versions of the 'nRF Mesh' applications .. (1) How can I tell if both apps are 'synced' to the same level of functionality/user interface...
Hi,
I want to test UART peripheral on nrf52840 by running example in path examples\peripheral\uart as it is.
Connection setup is:
nRF power source USB
nRF USB port...
Hi all
Previously, I used the nRF52832 with the interrupt-driven UART at 1Mbaud. But due to SoftDevice interrupts that blocked the UART-RX-IRQ for more than 6 bytes, I tried...
I am trying to set up fifo'ed uart. However, APP_UART_FIFO_INIT crashes with an error value 8. I traked back the reason into this nrf driver code fragment:
ret_code_t nrf_drv_uart_init...