I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hi, Is it possible to use the same UART instance for app core and net core to put the log messages? I am using an nRF5340DK board, which uses a separate COM port for each...
Hi,
My phone can find, but is unable to connect to, the FastPair locator_tag example. I have made no changes to the example code.
The most relevant error I can see in...
I would like to reduce the power consumption in normal operation mode.
Then I would like to reduce the operation frequency in the I2C, SPI and UART.
What is the command...
Hello everyone,
I’m trying to set up an nRF52840 dongle as a Thread radio co-processor to integrate with my Home Assistant setup. I followed the instructions in this Nordic...
Hello!
I have a device on which the S25HL01GT memory is soldered. The problem is that I don’t understand how I should work with .dts in order for this memory to work with...
Hi,
I started fesh on a new laptop, installed nrf Connect for desktop. I used VS Code to install the the latest nrf toolchain and sdk, verison 2.6.1, as they recommend that...
I create a linux docker container about nrf development environment. And the container host is windows11.
everything works fine except flashing function.
i passthrough...
Hello,
What would we expect the INFO.VARIANT FICR register's value to be with, for example, an nRF52811-CAAA-R7 vs. an nRF52811-CAAA-R7-B?
Right now I am seeing "AAA0...
Hi we are working on a matter project using ncs v2.6.0
Currently we are running out of RAM memory and that´s why we have moved to minimal logging by enabling
Now we...
I want to use 5" inch display for my project as nrf52840 is not able to handle that so I want to FT8xx EVE for the screen functioning? so did anyone has try this or any leads...
Dear support,
I performed a 48 hours- 20°C profiling of my 110mAh battery and managed to get my profile (really appreciate your nPM PowerUP tool. Helping a lot for development...
Hi.
I am working on a custom nRF52810 board (SDK 2.7.0).
When connecting LIS2DH12 via SPI in the .dts file, I see an error -->
.dts code -->
prj.conf -->
Please...
I try to capture the broadcast packets from the broadcast_audio_source application to investigate the BASE (which holds the configuration of BIGs, subgroups and streams)....
Hi DevZone Team,
I hope this message finds you well. I am reaching out to seek your assistance regarding the HID mouse implementation we are working on using the Nordic...
The question concerns using the nrf fuel gauge library for a setup with an nPM1300 PMIC and an NRF52840, implemented using the nRF5_SDK_17.1.0. Is it possible?
