Hello!
We are planning to purchase an electronic component nrf52840 and produce a finished product on it.
question
1. Will it work immediately on the ZIGBEE 3.0...
Good morning, I have a question about NRF Util. I need to make some changes in souce code of nrfutil for my own needs, but the most recent version, which is provided on Github...
Hi. I interested now for direction finding in nrf52 series. I have nrf52811, nrf52833 and other controllers. But i don't find any information how develop board for recievers...
Zephyr Eddystone example is connectable after power on of nrf52833 board. But after disconnect it becomes non connectable. How to fix it? And how to change advertisement interval...
We are looking for an experienced software developer, for existing board with using nRF Connect SDK. We are using nRF52840-dk.
Please, contact me if you are interested.
Hi,
I want to use nrf5340 dk board to debug nrf52840dongle, i have connected two board with a cable and have checked the signal is good( nrf5340 debug out p19 ------ nrf52840...
Hello all
the BLE module with the nRF52820 is programmed with a ble_app_uart_pca100e example from the nRF5SDK ver 17.1.0, according to the RSSI graph it seems it works ...
Hello Reader, I noticed two almost similar modules " DK buttons and LEDs" library and the "CAF LED & Button" library (or module). What is the difference between DK buttons...
I get the following error message from my device
àÓ FATAL: Exception occurred in Secure State [10.2 10:01:52.062]FATAL: ***** HARD FAULT ***** [10.2 10:01:52.062]FATAL:...
We have both native iOS and Android-apps that handle DFU-updates of our BLE-FW on our HW-devices. We are currently experiencing a dip in success rate (according to our firebase...
Hey Nordic,
The following are some specifications of my project.
nRF52833-DK
PCA10100
Softdevice is S122
Based on "ble_app_uart_c"
SDK 17.1.0
I am using VSCODE...
While testing a new nRF9160 based product with a Hologram SIM card, it connects fine in Minnesota, USA, but not in Winnellie NT, Australia.
Do you have insight into why...
Hi, I am using nRF connect sdk1.9.0 and modem firmware 1.3.1.
I have configured GPS to single fix mode.
err = nrf_modem_ gnss _fix_interval_set ( 0 );
err = nrf_modem_...
I have been trying for hours to get the LTE Sensor Gateway sample to work on my Thingy:91 (PCA20035) without success. According to the v2.0.2 README and the HCI low power...
Hi,
I would like to create a service that shows the current TX power of a peripheral during connection. I am using the Android nRF Connect app to connect to the nRF52833...
Hi:
I can't find the download address and description of the S110_NRF51822_7.1.0 protocol stack on your official website. I would like to know the version of BLE of this...
Hello, I encountered some issues with VS Code nRF environment. Kconfig will not open when clicked nor can I debug. When I try to debug it seems to be launching debug for a...
Hi
How can I read out the bootloader version from the main application which I defined in the zip packet (or merged hex) with nrfutil?
rfutil pkg generate --hw-version...
I'm using nRF Connect SDK v2.0.2 (in VSCode, w/ the plugin) on nRF52840-DKs.
Following the MPSL Timeslot sample , in the code shown below, I created a non-preemptible thread...
Hi
Currently I'm working on a Matter project with an nRF52840 board.
We have our own CSA issued vendor ID.
We want the light_bulb sample project to work with our vendor...
