Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
Hi ,
SDK：15.1.0
example：proprietary_rf \ esb_ptx
Because there is no UART function in the example, I want to add it.
The picture is everything I added, is it missing...
Hi Devzone team,
In our SDK, say SDK15.0, there is a head file called "sdk_config.h". It contains a line which looks like below:
// <o> NRF_SDH_BLE_GATTS_ATTR_TAB_SIZE...
WIth the upgrade to the new SDK, registering the callback handlers has been made more difficult to figure out.
The .sdh_ble_observers, .sdh_soc_observersers sections are...
Dear Sirs!
On one from 25 boards there is offset in ADC input about 30 ADC units. Vref = 0.6 V, Gain=6, 12 Bit ADC, oversampling 256 sample.
In other devices I do not...
Hi, Could you send me a sample to send "Hello World!" string from sender task to receiver task?
I am using C:\Nordic_Semi\nRF5_SDK_15.0.0_a53641a\examples\ble_peripheral...
Hi, I have a question regarding the behaviour of a button in the nRF App in Android, sometimes the button "READ STATE" in the "Generic On Off Server" configuration changes...
Hi,
I have managed to run DFU mesh example and successfully updated firmware of whole mesh network. Now i am looking for options to perform customized DFU over mesh . Lets...
We are experiencing issues with nrfutil being flagged as containing malware, see screenshot below. Has Nordic experienced this before, is there something we can do to stop...
Hi
I have reported this before and now that you are a quarter away from a fully featured mesh sdk can I ask you to please enhance the SDK so that you supply a function that...
I'm evaluating possibilities of BLE-LESC Pairing/Bonding with the ble_app_hrs peripheral on the nRF52840-DK with SDK 12.3 and SoftDevice s132. To see what's going on in the...
Is it possible to flash multiple custom boards using sagger DKs at the same time?, assume 2 custom boards and 2 DKs, would they be able to flash the custom boards in parallel...
There are many places in the file fsm.c that have this compile condition check
#if defined FSM_DEBUG
blabla
#endif
that is wrong. The compiler will ignore it. There...
Dear Nordic,
Hello, I have to configure 2 UART. I have saw this post .
however, I have made a demo version for the project without 2 UART function, so I hope to apply...
