Hello, I’m trying to compile code for a u-blox C209 AOA Tag. I installed the nRF Connect Extension Pack and was able to build normally.
After adding some unrelated paths...
This stopped working for me... Error is the following
Command failed: git ls-remote --tags --heads github.com/.../sdk-nrf
fatal: unable to access ' github.com/.../'...
Hello,
After a lot of efforts I managed to autoprovision and autoconfigure my nrf52840 board (provisioning and configuring inside the software and not through external app...
Hi there,
I am trying to interface at25xe321d with QSPI but it always end up returning zeros. Please find attached code and dts file for reference. Thanks Moh
Hi,
We have a custom PCB based on the nRF9151 and nRF7002 for a tracking use case, supporting both indoor (Wi-Fi scanning) and outdoor (GPS) positioning. Our firmware is...
When version 1.0.0 of nRF54L15-DK evaluation kit will be available and how to distinguish the version when ordered from distributors like Digikey?
In discussion here:
...
-> How to transfer data from one thingy52 device to another thingy52 device. If i have 2 thingy52 devices, I'll send data to 1st tingy52 then 1st thingy52 device will send...
I am working on an mbed nrf51-DK powered Bluetooth Low Energy project. I have been developing various GATT services, however, I have now found my project has got "stuck" on...
Hi,
I'm using 3rd Generation of the nRF51822 with SoftDevice 8.0.0 and SDK 10.0.
There is an example in the SDK installation folder which shows how to use the TWI transaction...
Hello,
I have PCA10004 rev 2.2.0 evaluation kit and have tested S110 applications with SDK9.0 and softdevice 8.0.
Now I am working on S130 stack, softdevice v 1.0.0 and...
Hello,
I am working on S130 stack with version 1.0.0 and SDK 9.0 . I am testing the example of ble_app_hrs_rscs_relay_s1 project and it is working as a peripheral but the...
Hi nRF team,
I read somewhere that the sensitivity of the nRF52 is degraded when the internal DCDC is enabled. Can you confirm or dismiss this? If true, what is the sensitivity...
Hi,
I want to use nRF52832 for our new development.
So I have to get examples source code like nRF51822's Keil Pack Installer.
Where Can I get example source code for...
I saw the video of csr mesh network. I want to try something like that using nrf51822. I have read the documentation provided in the link link
. But I only got a rough idea...
Hi,
I am looking for an wearable solution which should be able to full duplex audio transfer over Bluetooth. Is this possible with BLE 4.1/4.2. As here battery life is...
Greetings. Could you provide more information on the issues with GPIO located near the radio in the nRF52 (PS 18.2.1)? Specifically, what is considered "high frequency digital...
I've created a BLE Peripheral project to test maximum possible throughput for the Notify of a single characteristic. I've also created a Central based on the new BLE Central...
Hi: I want use all eight ADC channel, But I don't know how to get different channel conversion result.
I write my code as follow:
void adc_config(void)
{
const...
Hi,
I'm using the 3rd generation of nRF51822 with S110 v8.0.0 and the SDK 10.0.
In my application i'm using the uart core to communicate with the external device.
I'm...
I'm not sure why I didn't notice this sooner.
When trying to do a bonded DFU with a Nexus 6P and Master Control Panel it seems to get stuck in a loop reconnecting.
I...
Hi I trying to connect Altimeter ( mpl 3115a2) to the nrf52 development kit. Can someone guide me how to do it (pin connection). I have followed the example given in the sdk...
