Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
About 44 minute mark of Measuring distance with the Nordic Distance Toolbox - Nordic Semiconductor , Paal mentions tuning is needed for custom boards. In slide 38 of /cfs...
Hello all,
I am currently trying to test out the programming functionality of the SEGGER JLink Plus on the NRF52840-DK. I am trying to do this in preparation for programming...
Hardware: nRF52832 on the nRF52-DK
SDK: nRF Connect v2.0.0
IDE: Visual Studio Code 1.73.1 with nRF Connect for VS Code (v2022.11.140) extension
I'm trying to get familiar...
Hi Nordic/Zephyr Community, observer behavior:
-- west build: generating a build system LIBRARY_SDK_BASE:= C:\cm\projects\zorbit\library_sdk ZEPHYR_BASE:= c:\cm\ncs\v2.1...
I'm testing out my new PCA10040 dev board. I can see the board in Windows Explorer when it's connected and I can see the two preloaded files as in the attached screen shot...
Hello Community / Nordic How can I have a boolean property in my mp2723 device driver devicetree dts or overlay. I am using NCS v2.2.0 in MS Windows 11 with VSCode 1.17.2...
Hello!
Using nrf_gpio.h enables P0.00 port control, but using app_timer.h together makes port control impossible.
I don't know if the code I wrote is the problem or...
I am using zephyr 3.1.0 and i build blinky pwm and rtc code from zephyr but it is not building i am using nucleo_u575zi_q board but in dts of board pwm and rtc is not there...
I modified the nrf9160 https_client sample to make a GET request to a web server and retrieve a JSON response. Unfortunately the rec_buf always ends up with an HTML response...
Hello everyone!
I've been struggling to get over this error when attempting to use an augmented Thread project based on the thread_mqtt_sn_client_publisher example. Would...
According the nordic documentation of the AT command +CEINFO, the value of CINR is in dBm.
Other source (outside Nordic) mention dB as common unit, e.g. LTE signal quality...
Hello everyone,
I'm trying to display internal sensor on NRF51422-DK (PCA10028) on my Android phone (v.12). I'm using Keil for programming and nRF Toolbox to see UART results...
ble_gap_addr_t xyz;
sd_ble_gap_addr_get(&xyz);
/**@brief Get local Bluetooth identity address. * * @note This will always return the identity address irrespective of the...
Hello, I have three questions that i could not clarify in an adequate amount of time via Google and DevZone.
Setup: I am working on a custom board equipped with nRF52805...
Good day
I am trying to use lwm2m_engine_set_float on the lwm2m_client sample to change the sensor value.
Referring to the above link, the sensor value is set in the...
