Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi,
I am trying to understand the pstorage to record a log for temperature. In my code, I can call pstorage_init(), and clear a block but when I try to store some data...
I would like to source a compact BLE board to act as a lock controller developed with with a matching transceiver for use in a fob and an app.
It would toggle the pio and...
Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
Hi.
I am using Central's ble_app_uart_c_pca10028_s130 which is a sample of nRF51822.
I would like to see the timestamp of the advertisement acquisition I receive from...
Hi,
NRF52840 datasheet section "5.4.4.2 64 MHz crystal oscillator (HFXO)" mentions crystal tolerances being dependent on packet size.
It is not clear to me, what layer...
Hi,
I've had the nRF52 and Segger Embedded Studio on my old computer. But the old computer is dead now.
I am trying to create the same environment on my new computer....
Hi nordic
I run the HID keyboard with SDK 15.2 and connected to IOS's nrf conncet.
but i can't see the HID service in the table.
how can i use the nrf connect to debug...
Hello there,
I'm ripping my hair out hear reading everything I can to get the non volatile memory reading and writing.
I have a nFR52840 dongle and I dont want to...
Hi everyone,
I have a project that needs to use multiple saadc channels but I don't want to use ppi but use app_timer. So is there any way I can change between saadc channels...
I'm using a timer to trigger pins via PPI & GPIOTE. Setting the PPI TEP to the GPIOTE task works as expected. However, when I try to set a second pin via GPIOTE task via PPI...
hello Nordic
i am working with nrf52832 soc with SDK 16.0, S132 V7.0.1
following this path:
https://devzone.nordicsemi.com/nordic/short-range-guides/b/software-development...
Hey,
There is a microSD connector on the bottom of the nRF9160DK (v.1.0.2). Is there a way to utilize it as an external memory? I can't find any information about it on...
Hello,
I've been studying Bluetooth technology for a few weeks. I wanted my first to implement a simple key finder device, as my first project. I was doing some research...
Hello, For our nrf52832 custom board developed using nrf SDK 14.2, I need to turn OFF and ON LED accurately in terms of ms, hence after going through this page, I used Single...
Hi,
We are developing a device that should work in multiple mobile networks, and some of these are known to provide no DNS server. As using a fixed IP address for our cloud...
Hi,
I want to read the data from the a cceleration sensor by I2C. Several days ago, I added the code about twi bus to "ble_app_template" example , it worked well. But today...
I have a custom board, I am using to evaluate nrF52811 from eclipse (I just prefer this over SES).
I have installed S112 on the flash and also my application at 0x19000...
I'm communicating with N25 flash memory, the page size is 256 bytes. there is a page_program command which can write up to 256 bytes. there is no way to write in the middle...
