Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
I wasn't receiving any log messages while debugging the ble_app_uart_c example using SES so I enabled appropriate logging functions and set them to level 4 in config.h. Still...
We are using NRF_SDH_DISPATCH_MODEL_APPSH, and are generally very happy with it (especially for BLE events). However, I'm trying to retrofit error handling around complex...
SDK: 15.3.0 Example: ble_app_multirole_lesc Device: EYSHJNZWZ (nRF52832)
I define the following macros in "Section Placement Macros".
Can I use these macro values in my...
When the boot loader calls the sd_mbr_command it does not get updated.
sd_mbr_command_t sd_mbr_cmd;
sd_mbr_cmd.command = SD_MBR_COMMAND_COPY_BL;
sd_mbr_cmd.params...
SDK: 15.3.0 Example: ble_app_multirole_lesc Device: EYSHJNZWZ (nRF52832)
I recognize by default that the top address of the app is 0x26000. I want to change the top address...
I need to measure current of loads attached to NRF52832 using current transformer(CT).
I can use SAADC library to read ADC value. But to measure current I have to know the...
I have a question about PeerManager.
SDK: 15.3.0 example: ble_app_multirole_lesc (I changed the source from the sample) deviceA: EYSHJNZWZ (nRF52832) deviceB: Android (ver9...
Dear All,
We would like to automate the trst procedure of our device in LabWiew because in this tool we are doing also electrical measurements.
We have tried nRF connect...
Hello,
I'm running custom firmware on a nRF52840 based DK (Rigado BMD-340).
The log from the nRF Connect app is as follows:
Could anyone help explain the error...
Hi,
I am using nrf mesh sdk v3.2.0 and I would like to combine our custom service within the mesh server example (includes the proxy service). Using info from other threads...
We are having issues with UART communication on the nRF52840. Using a logic analyzer, we have found that the transitions happen too quickly. This causes the receiving MCU...
I have been working with Thingy:91 for three weeks now. Everything works nicely, however, I could not get any GPS location from it. I am using Rogers simcard which is a local...
Hello everyone. My project is getting quite complex so I will try to abridge. (Mesh SDK 3.2.0) I am trying to send wifi credentials from an android application (derived from...
Hi guys,
here in Croatia I'm trying to connect to NB-IOT network using nrf9160.
Here are the commands i am executing:
After this command modem does not accept any...
