Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
The example projects I am referring to is located here:
nRF5_SDK_15.2.0\examples\iot\mqtt\lwip\subscriber\pca10056\s140\ses\iot_lwip_mqtt_subscriber_pca10056_s140
nRF5_SDK_15...
Hi all,
I successfully ported the Semtech’s LoRaMac-node (from official GitHub, master branch) to a custom assembly of two dev boards : the NRF52832 (Dev Kit PCA10040) from...
Hi,
I am trying to use UART interface on a nRF9160DK board to connect a rs-232 to rs-485 module for the purpose to make nRF9160DK a Gateway.
But I have no idea where to...
Hi,
Are there any known Android bugs where Android should not bond, but does? I have tried searching the web without too much success.
My central device is an older Android...
Hi,
Is it possible to add scan response with extended advertisement packet?
When I try to add scan response, then I got error NRF_ERROR_INVALID_PARAM.
I am using a nRF52840...
Hi there,
I am using two nRF52 one as Master and the other as Slave SPI, but I am facing an issue with the slave side, because when I use NRF_DRV_SPI_FREQ_125K it get some...
Hi,
I am using the nRF52840 on a custom board with SDK15.2.0 with SD S140 6.1.1.
My current BLE connection parameters are below which allow connection to the nRF Connect...
With Mesh SDK 3.0.0 , i have tested with light switch example with one client and one server, it works. My question is is it possible that one server can communicate to another...
Hello,
I have developed simple scanner application that scans for beacons (apple, nordic and of own type). It prints data about beacons over UART. I have installation where...
Hi,
due to some evaluation effort of nRF52840 Dongle, I went through whole Zephyr project building of their Bluetooth hci_uart example. After couple of ardous hours(or more...
Hi there,
To do LESC with some peripherals supporting OOB Rx, and some not, and the central supporting OOB Tx, I was wondering how to correctly enforce the OOB for the right...
Hello,
I am beginner with NRF 52 DK. I am trying to change the uart example using NRF 52 with SDK 15.02, so that I would send message after pressing button to my PC via...
A temperature and humidity acquisition device uses NRF52832, watchdog, RTC timer, external touch button interruption, BLE open state, feeding the dog every minute through...
Hi,
I am having 2 nRF52 DK boards and I have to blink the leds of one nRF board with the help of another nRF 52 DK buttons and vice versa .
How to do it?
