Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
Hello Nordic Experts,
I am developing the pairing in a central. I am working on nRF52840 DK with nRF5_SDK_15.2.0_9412b96 as the cnetral and I have an iOS app as the peripheral...
We are using the nRF52832 with S332 v2.0 of the stack. We have recently been testing concurrent operation of a BLE peripheral connection and an ANT bidirectional master. The...
Hi all,
I'm using nRF52840 Development Kit and Nordic SDK v15.2.0 with soft device v6.1.0
I'm using ECDSA Cryptographic libraries for a BLE related project. I want to...
Hello,
I am working on Low power and Ultra Low power.
I am using the nrf52832 chip as well as the breakout board. In SYSTEM-ON mode power consumption around 6 mA and in...
How do I calculate round trip delay (time taken for packet to travel from peripheral to central(PC) to peripheral again)? Is the existing time calculation in the example code...
Hi,
I have some troubles using TWI easy DMA. I set EASY_DMA flag to 1, but I can't see any results in my performance tests. Can anyone explain me the required steps? ...
I am looking at the android version of the Blinky application and was trying to make some modifications to enable the LED3 on multiple boards (peripherals) to turn on from...
Hi,
In a peripheral, a notification is sent to the central every 10ms. (payload less than 20 bytes)
I use : radio_notification_init(6,NRF_RADIO_NOTIFICATION_TYPE_INT_ON_ACTIVE...
i want to read the temperature ..... my temperature data is executing from 0 degree temperature ...is there any way to execute only actual data instead of starting from 0...
I'm probably not using the good terminology here... let me explain my application.
I have an existing board which has all the logic implemented in an STM32 MCU. I now need...
Using Softdevice 132 version 6.1.0 I issue the request for scanning by calling sd_ble_gap_scan_start() with: ble_gap_scan_params_t scan_params = { { .extended = 0, .report_incomplete_evts...
Hi all,
I want to measure higher frequency (8 MHz) count/ticks by using the lower frequency (32 KHz) is there is any method to do it or any examples.
I want to measure...
Hi,
I am evaluating the nRF52840 with the Segger IDE.
I am about to experiment with Bluetooth, but I have a hard time understanding the different protocols/softdevices...
Hi, recently I've been confronted with this issue that all of my stocked nRF52832 ICs would not work with the lastest SDK, which later turned out to be engineering samples...
In the light of recent news like this one, https://arstechnica.com/information-technology/2018/11/bluetooth-bugs-bite-millions-of-wi-fi-aps-from-cisco-meraki-and-aruba/ ,...
