Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
Hello sir,
I am using nRF52832 board and interface with 3 axis accelerator reading ADC for 3 Channel. I have use sample code for controlling in timer/RTC mode. My ADC is...
Hi,
I am working on NRF52 custom board with 3.7mA 27mAH battery, working on BLE app UART example SDK11 with SoftdeviceS132V2.0.
I made BLE advertise for 20 sec interval...
I prototyped a nRF52832, WLCSP package, with a fab (PCBA) and put jumpers between my 32Mhz crystal and the chip, attempting to connect with a j-link in SWA mode, I cannot...
Hi. I'm using nrf52832.
Now I'm using HFXO, LFXO to operate BLE. As I know I should use HFXO to operate BLE.
What about LFXO? Can I use internal clock(LFRC RC osc) instead...
Hi,
I am working on the latest version of SDK (v14) and SoftDevice(v5) on nRF52382. When I call the sd_gap_disconnect it returns NRF_SUCCESS. However the BLE_GAP_DISCONNECT...
I was trying to verify the DFU functionality on SDK 14 on nRF52832. Here is what I did.
1. Using nRFgo to erase all
2. Program bootloader/soft device with C:\svn\nordic...
Hi,
I am using SDK v12.2 and gcc compiler. S132 softdevice for nrf51822 controller.
And i am using s132 softdevice.
I want to connect multiple nrf51 devices (approx. 14...
Hello sir,
I am using nRF52832 board and interface with 3 axis accelerator reading ADC for 3 Channel. I have use sample code for controlling in timer/RTC mode. My ADC is...
Hi,
I'm doing some measurement on the radio peripheral of the nRF52840 using the generated events and a timer which is set to run at 16MHz. Radio events and Start/Capture...
SDK version: 13.1
Hardware: nRF52832
Eclipse version: link text (I could not get the marketplace working in the latest Mars Eclipse version, so I downloaded this version...
I am evaluating the sdk14 ble_app_uart example. I am able to run this code and connect to this uart service but do not see messages get passed to the uart pin. Only when I...
I am using a nrf52832 Development Board with s132 for some BLE applications. I developed a beacon app, set for BLE peripheral, and every reading of the advertising from this...
Hi,
I'm using NRF51 DK board and i am following characteristic tutorial available. I am able to send temperature value over Bluetooth by using light blue app.. Instead of...
I am using nRF connect to debug an application on a nRF52832. When I perform a scan, I can see the UUID of the nRF52832 device I want to connect to. Where is this UUID stored...
