Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
Hello,
I downloaded the nRF Blinky app (for Android) here :
github.com/.../Android-nRF-Blinky
I'm looking to modfy the code to have an auto connection. For this, I...
As far as I can tell, the application is set to invalid (settings.bank_0 = BANK_INVALID_APP) after the application has been successfully deleted ( devzone.nordicsemi.com/...
im trying to use nrf_drv_timer_t with timer0 but I get identifier "TIMER0_INSTANCE_INDEX" is undefined error. TIMER0_INSTANCE_INDEX is defined in nrf_drv_config but this file...
Hello,
is the nRF51822 able to function as repeater or range-extender, repeating BLE signals from explicit two BLE devices (with known addresses)?
I know there are specific...
Hi,
we are developing a custom board based on an NRF51822 and for security reasons are using whitelisting.
So far this worked well with different iOS and Android devices...
i try to modify the saadc exemple program by includding pwm , but after including header file in the application , source in driver, and includding target, i get error always...
Hi All, anyone aware of a module certified for BLE v4.2 protocol? It doesn't have to be built on the Nordic chip, I'm interested in any other one too. Many thanks!
Hello,
I am using PCA10028 and sdk12.2. My challenge is nrf51822 resets after it executes the code for the first time.
I am storing few values in flash. After that I am...
I'm following this tutorial for creating a basic custom service using the ble_app_template from sdk 13 github.com/.../custom_ble_service_example
I've filled in the following...
Hello,
I am using PCA10028 and sdk 12.2.0. Now I have interfaced temperature sensor and I am storing 4000 readings from sample to flash. Once all the 4000 samples are stored...
When I enable DLE with a max MTU size of 247 (NRF_BLE_MAX_MTU_SIZE = 247) and PDU payload size of 251 (opt.gap_opt.ext_len.rxtx_max_pdu_payload_size = 251) and a max characteristic...
log.txt I have programmed my nRF smart beacon with example peripheral code with DK52. My beacon now flashes red. I am using the nordic sniffer to sniff ble packets in wireshark...
Hi,
I will be using ble_uart application code in my nRF52 Evaluation board. With nRF52 EVK I will be connecting external module over UART communication. I want to detect...
i am having trouble with pwm module 2. only two of the channels are working but not the third nor the fourth.
i tried pwm module 1 but im having the same problem there. i...
