VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
On SDK 11.0.0 only ( NOT the alpha release )
Do not judge the quality of SDK based on number of entries here. This thread should be considered part of Nordic effort...
On SDK 10.0 only
Do not judge the quality of SDK based on number of entries here. This thread should be considered part of Nordic effort to main the quality of the release...
I am testing nrf5 IoT tcp client example. (in \nrf5_iot\examples\iot\tcp\client)
DK side:
IP:2004::213:ddff:fe4c:6032
run as client.
2.6lowpan border router...
I'm using the ble_app_template of SDK11. but I dont have an external oscillator, so the run time freeze at ble_stack_init
in this answer , the solution is to relace NRF_CLOCK_LFCLKSRC_XTAL_20_PPM...
Hi,
I have a NRF52DK (Chip Label: PCA10040; V0.9.0; 2015.44; 682646724) and when i try to start the DK as described in the getting startet page, Step 5 failed as LED1 is...
Hi,
I am planning to make a program so that when a beacon goes far away a specific distance (around 5m) then the led should light up.
I have taken some measurements...
Hi,
I have a couple of eval boards that were created for software and hardware development. We have two versions of the nRF52832 on these development boards. I know that...
I am using nrf51822 powered by a 3.3V regulator in a li-ion powered application. We have a high current load that we're controlling with PWM at 20kHz. Radio performance is...
I want to bond with an peripheral, which has static passkey hardcoded in it. If I want to bond with it with MCP, I get an request for passkey, I can then bond and encrypt...
My environment for this is
Ubuntu 14.04
ecipse Mars2
ble_app_uart project of Nordic SDK11(makefile project)
armgcc
nRF52 PCA10040 Nordic board
ERROR...
I am trying to figure out how to exit a loop of my program using a button press on the nRF Toolbox UART app. Say it's button 4 for sake of giving it a value. I am using an...
Hello,
I've been trying to use nRF Connect 1.0.0 on OSX 10.11.6 with a nRF51822-powered board ( this one, to be precise ). Whilst nRF Connect finds the serial port and...
Hi,
I'm complete nordic newbie and asking you for some help.
I have 2x 81522 ICs, one is QFAAC0 and the other one is QFAAH1, both QFN48 packaged.
(1) looking at infocenter...
Hello I'm trying to learn your API using nrf5-ble-tutorial-advertising example. Over all the example is much help and API documentation is quite good. But part of API code...
Hi,
I am trying to do a GPIO operation every one second repeated in 51822. I am using app timer to get this work done. The current average consumption is 45uA/H. The handler...
